Machine Kinematics
solved, then drawn
Concept

Pitch — where it appears

The spacing between repeated features on a wheel or a rack, measured along the circle or the line they sit on. It is the unit a mesh is described in: the contact ratio counts pitches of contact path, and two wheels mesh only if their pitches agree.

Named by 23 essays across 8 fields — each of them below, with the objects they name alongside it.

Six surfaces, six groups, six pairs. The six lower pairs, drawn as the surfaces they are. A lower pair is two bodies touching over a surface rather than at a point or along a line, and that is the same thing as saying the surface slides on itself — so what the joint permits is the surface's own symmetry group. Each caption is computed from the surface's normals and not from the pair's name: a plane gives three freedoms and planar motion, a sphere gives three and spherical motion, a plain cylinder gives two, a shaft with collars gives one rotation, a prism gives one translation, and a thread gives one screw whose pitch comes back as the thread's own lead. Eleven surfaces were tried and six groups came out, which is where the number in every textbook's table comes from.

A joint is a surface that slides on itself

Twenty-two fields of this site have declared their joints and then counted what those joints take away. A count cannot tell a pin from a slide — both are one. What a joint actually permits is a set of displacements closed under composition, and it can be computed from the shape of the surface: one linear condition per point, and the answer is a null space.

pairs · Pair A cycloidal cam at 60°. A 20-unit rise over 120°, a dwell, a return and a dwell. The dashed curve is the pitch curve — where the roller's centre travels — and the solid one is the surface that has to be cut, which is the pitch curve offset inward by the roller radius along its own normal. The pressure angle at this instant is 25.5°: the angle between the follower's direction of travel and the normal to the surface, and the number that decides whether the follower jams in its guide rather than sliding.

Prescribing motion

A linkage gives the motion its geometry allows. A cam gives the motion it was asked for, which sounds like an improvement and is a trade — the displacement becomes free and the derivatives stop being.

cams · Cam The involute, unwound. Hold a string taut against a circle and unwind it: the end traces this curve. Two properties follow immediately and between them they are the whole of gear geometry. The string is always tangent to the base circle, and it is always perpendicular to the curve. So the normal to an involute at any point is a tangent to its base circle — measured on the generated points here, to 2.3e-5 — and when two involutes touch, the common normal is a line tangent to both base circles, which does not move as the gears turn.

Why a tooth is an involute

A gear tooth is not a shape anybody chose for its looks. It is what one requirement forces — that the ratio of the two shafts' speeds stays exactly constant while the contact point slides along the flank. Impose that and the curve is essentially determined.

gears · Tooth Every surface tried, and the group it permits. The census the six lower pairs come out of. Each row is a surface, sampled at 240 points; the freedoms column is six minus the rank of a matrix with one row per point, saying that the velocity a twist gives that point is tangent to the surface. Nothing is fitted and no shape is recognised — the surface's own normals write the matrix down. Three different surfaces of revolution give the same group, which is the content of the classification; two surfaces give nothing, which is what almost every surface gives. Eleven surfaces, six groups. The last column is the ratio of the smallest singular value kept to the largest discarded, so a row reading 10¹⁵ is not near being reclassified by anybody's tolerance.

Six, and no others

Eleven surfaces were handed to the same computation and six groups came out. A cone, a torus and an ellipsoid of revolution give the same joint; a scalene ellipsoid gives none; and the list does not grow when more surfaces are added, because a surface's symmetry group has to leave a two-dimensional set alone and only six groups can.

pairs · Pair 20 teeth driving 32. Both flanks generated from the involute, not approximated, at a pressure angle of 20°. The orange line is the line of action — tangent to both base circles, and the only place contact happens. Its length between the two tip circles divided by the base pitch is the contact ratio, 1.612 here, which means that for 61% of the cycle two tooth pairs are carrying the load and for the rest just one. The velocity ratio is 0.6250, and it is constant because the common normal never moves. The dashed extension runs between the two base tangency points, which are 8.89 mm apart; the heavy part is where contact actually happens.

What happens in a mesh

Contact between two gear teeth happens only along one straight line, and only over part of it. How much of that line lies between the two tip circles, divided by the base pitch, is the contact ratio — and if it drops below one the drive periodically stops being driven.

gears · Tooth One point, six groups, six shapes. A group has no picture, so here is the next best thing: fix one point of the moving body — the marked one — and draw everywhere the group can send it. A prismatic pair sends it along a line, a revolute round a circle, a helical along a helix, a cylindrical over a cylinder, a spherical over a sphere, a planar over a plane. Those six shapes are the six surfaces the previous figures drew, which is not a coincidence and is the field's first argument read backwards: a lower pair's surface is an orbit of its own group, which is exactly why the surface can slide on itself.

The count cannot tell a pin from a slide

A revolute, a prismatic and a helical pair all take five freedoms away in space and leave one. Grübler adds the same number for each, the constraint rank measures the same number for each, and the three joints have nothing whatever in common — one sends a point round a circle, one along a line, and one along a helix at a rate the joint decides.

pairs · Pair Undercutting, either side of 17.10 teeth. Five gears, drawn whole and scaled to a common pitch circle so the tooth counts can be compared by counting them. The dedendum sits a fixed 1.25 modules below the pitch circle and the base circle sits at r·cos α, so as the tooth count falls the base circle rises relative to the root. Below N = 2/sin²α = 17.097 it rises above it, and the part of the flank between them lies where no involute exists — the cutter removes it. The familiar rule says seventeen; the exact figure is 17.10, so seventeen undercuts slightly and eighteen is the smallest count that does not. The teeth are not to a common scale, because at a common module the small gears would be unreadable.

Undercutting, and the seventeen-tooth rule

Below a certain tooth count a standard cutter eats into the flank it is supposed to be forming. The count is quoted as seventeen. The formula gives 17.097, which means seventeen undercuts slightly and eighteen is the smallest that does not — the rounding went the convenient way.

gears · Tooth A 34-unit roller on a 20-unit base: the cam cannot be made. The outer curve is the pitch curve — where the roller's centre has to go, which is just the base radius plus the follower's displacement, plotted in polar coordinates. The inner curve is what has to be cut: the pitch curve offset inward by the roller's radius along its own normal. Where the pitch curve bends more tightly than the roller is wide, that offset crosses itself, and the metal the profile needs has already been removed. The tightest radius of curvature here is 19.43 at 85°, against a roller of 34 — so the cam is undercut by 14.57 and no amount of care in manufacture recovers it. The pressure angle, meanwhile, peaks at a perfectly comfortable 21.2°: this cam fails a test it never looked like failing.

The cam that cannot be cut

A cam has to be big enough for two reasons, and they are not the same reason. One is that the follower will jam in its guide if the pressure angle is steep. The other is that the roller will gouge the profile if the curvature is tight — and there is a combination where the pressure angle is comfortable and the cam still cannot be manufactured at all.

cams · Cam The twelve kinds of freedom, and which are joints. Every connected group of rigid displacements, up to where its axis points and where its origin sits. There are twelve, the height on the page is the dimension, and a line means the lower one is contained in the upper — computed by asking whether each generator of the smaller lies in the span of the larger, with all twelve built about a common axis. Filled discs are joints: six of the twelve are the symmetry group of a surface and can be a single pair, and six are not and have to be built out of a chain. There is nothing at dimension five, which is not obvious and is checked rather than assumed: twenty thousand random five-dimensional subspaces of the twists were closed under the bracket, and every one generated the whole of the six.

Twelve kinds of freedom

Every set of displacements that is closed under composition is one of twelve, up to where its axis points. Six of them are joints somebody sells. Four are motions a designer may perfectly well want and cannot buy at any price. And there is nothing at all of dimension five — checked here on twenty thousand random subspaces, every one of which generated the whole of the six.

pairs · Pair 11 teeth, cut with three different shifts. A 11-tooth gear cannot be cut with a standard rack without the cutter eating into the flank near the root — the tooth is undercut, and what it loses is exactly the part that does the work. The fix is to hold the cutter further out by a fraction x of the module. Here the threshold is x = 1 − z sin²α / 2 = 0.3566, measured rather than quoted: at 0.347 the gear still undercuts and at 0.3566 it does not. What the shift costs is at the other end of the tooth. The tip thickness falls from 0.606 to 0.240 of a module, and a tooth shifted far enough comes to a point and breaks — so the technique has a ceiling as well as a floor.

Moving the cutter out

A gear with too few teeth is undercut by the tool that generates it, and the fix is to hold the tool further out. What that does to the tooth is easy to say. What it does to the pair is not what most readers expect — the two gears no longer mesh at the centre distance the sum of their radii would give, and the pressure angle they run at is no longer the one they were cut with.

gears · Tooth A screw of pitch 0.25. A single screw drawn from its own decomposition. The six numbers of the twist go into a decomposition that returns a direction, a point on the axis and a pitch of 0.2500; the helix is then the path of a point at radius 0.5 about that axis, advancing 0.250 along it per radian turned. Over 1.15 turns the point advances 1.806 — the pitch times the angle, which is what pitch means. This screw is a screw.

Every motion is a screw

Chasles showed that any rigid displacement whatever is a turn about some line together with a slide along that same line. Not approximately, and not usually — always, with the line and the amount of slide computable from the motion. It is the fact that makes spatial kinematics a subject rather than a pile of special cases.

spatial · Spatial Three bars, and no rotation left. Each of a delta robot's legs ends in a parallelogram, which keeps the bar on the platform parallel to the bar on the arm. That leg therefore permits the platform no turn about either direction perpendicular to its bar: it imposes two couple constraints, drawn here as rings about the directions they act on. Three legs impose 6; together they span only 3, so 3 are redundant. What is reciprocal to them is three couples — three pure translations, and the platform cannot turn at all.

Why the platform stays flat

A delta robot has three legs and three freedoms, and there is no obvious reason those freedoms should be the three translations rather than some mixture. The reason is a parallelogram in each leg, and the argument from there to "the platform cannot turn at all" is a constraint computation that takes six wrenches and a rank.

parallel · Parallel One point, six groups, six shapes. A group has no picture, so here is the next best thing: fix one point of the moving body — the marked one — and draw everywhere the group can send it. A prismatic pair sends it along a line, a revolute round a circle, a helical along a helix, a cylindrical over a cylinder, a spherical over a sphere, a planar over a plane. Those six shapes are the six surfaces the previous figures drew, which is not a coincidence and is the field's first argument read backwards: a lower pair's surface is an orbit of its own group, which is exactly why the surface can slide on itself.

What a point sees

A group of displacements has no shape, so the only picture of one is what it does to something. Fix a point and the six lower pairs draw a line, a circle, a helix, a cylinder, a sphere and a plane — the six surfaces the pairs are made of. And two of the twelve sweep the same surface and are still different groups, which is the honest caption on the whole method.

pairs · Pair Whose constraints stay put. The largest principal angle between a mechanism's screw system at the start of its motion and at each later position. The 3 mechanisms whose motion lies in a subgroup of the rigid displacements — planar, spherical, translational — never leave the same subspace, and read between 1.9e-6 and 3.0e-6 degrees, which is the precision of an arccosine near one rather than a movement. The paradoxical ones turn through 49° and 57°. Every curve runs over its own range of motion, because Bricard's linkage assembles over 120 degrees and a shared axis would hide it.

Two ways to be overconstrained

A planar four-bar and Bennett's four-bar report the same redundancy, the same rank and the same wrong count. One of them is overconstrained at every set of link lengths; the other at exactly one ratio and nowhere near it. The difference is not in any of the numbers so far — but it is measurable, and the measurement is an angle.

spatial · Spatial A chain is a strand with a smallest piece. 53 teeth driving 11 at a pitch of 12.7 mm. The taut strand is drawn as this field computes it; inside each pitch circle is the polygon the pins actually sit on. The two agree on the straight spans and not on the wraps, and the gap is what the applied field's chordal action is: the effective radius swings between R cos(π/n) and R within every tooth, which is 4.05% on the small sprocket and 0.176% on the large one. A strand has no such number, because a strand has no pitch. positioned by solving, not by drawing.

A chain is not a strand

A chain has a smallest piece, and two things follow that no continuous model can have. Its pins sit on a polygon, so the radius that matters swings by 4.05% within every tooth of an eleven-tooth sprocket — and its loop must contain a whole number of pitches, so the centre distance that closes it comes in steps of 6.4834 mm.

strands · Strand The cylindroid at 75° and 1.00 apart. Every screw in the two-system spanned by two revolute axes 1.00 apart along their common perpendicular and 75° out of parallel, drawn as its own axis. The axes sweep a ruled surface — the cylindroid — and each generator carries a pitch, running from -0.384 to 0.652 and reaching its two extremes on the two principal screws, which cross at a right angle at the centre. The surface is 1.035 long along its own axis, which is exactly the spread of the pitches: a cylindroid is as long as its pitches are far apart.

The smallest screw system has a shape

Add two screws together in every proportion. The results do not scatter — their axes sweep a ruled surface, with the pitch varying along it between two extremes reached at right angles to each other. It is a picture nobody would guess from the algebra, and it is the object that says what two joints between two bodies leave free.

spatial · Spatial 53/11, instant by instant. The ratio a 53-tooth sprocket and a 11-tooth sprocket actually deliver, against the driver's rotation. The quoted 4.818 is the flat line, and it is exactly right as an average — the mean over a turn comes out at 4.8182, which the computation is never told. Within every tooth the ratio swings from 4.756 to 4.948, a fluctuation of 3.99%. The sharp corners are pins seating: the identity of the pin the strand runs from changes 53 times a turn on one sprocket and 11 times on the other, and the two do not coincide.

The chain is a polygon

A chain's pins sit on a polygon, so the radius that matters swings by 1 − cos(π/n) within every tooth: four per cent on an eleven-tooth sprocket. The quoted 53/11 is the mean of that, exactly — and how much of the fluctuation reaches the back wheel is decided by the fractional number of pitches in the taut strand, which nobody adjusts and which can take the drive from perfectly uniform to two per cent.

applied · Tooth A joint with no way out in the plane it is drawn in. A dovetail. The tail is wider at its far end than at the mouth it went in through, so every direction out of the mouth is blocked by a slanted face and every direction further in is blocked by the floor. In the plane of this drawing the joint cannot be taken apart at all, and the direction it does come apart in is the one the drawing does not show. The moving part touches the rest at 3 faces, each contributing one inequality on the direction it may be translated in — the direction must not have a negative component along that face's inward normal — and the set of directions that satisfy all of them is a cone in two dimensions rather than three, because a translation has no moment term. That is why a removal cone can be drawn as an angle where a mobility cone cannot. Here it is empty: every direction is refused by one face or another, so the part cannot be taken out by any translation and cannot have been put in by one either. That is a statement about the assembly and not about the part, and the direction the joint does come apart in is perpendicular to this drawing. positioned by solving, not by drawing.

A cone has no size

What a set of contacts permits is a cone of twists, and a cone is closed under positive scaling by definition — so nothing about it changes when the part it holds is made bigger. Except that a twist is a screw, a screw has a pitch, and a pitch is a length.

holding · Restraint Every position loses its hold at -150° and 30°. The smallest singular value of the six leg lines of the Gough–Stewart platform, held level, as it is turned through a whole revolution at 4 positions: (0, 0, 2.4), (0.4, -0.3, 2.4), (0, 0, 3.2), (-0.5, 0.2, 1.8). At -150° and 30° all 4 curves reach zero together — the largest of them is 9.7e-9 — and 1° either side the least is 1.28e-3. Nowhere else does any of them touch zero.

A yaw that is singular everywhere

Turn the standard hexapod platform 30° about the vertical, hold it level, and it is singular: not at one pose, but at every position it can be put in, with one screw motion that none of its six locked legs can resist. The angle is not a property of the dimensions. It comes out of one line of trigonometry that no spread of the anchor points can change.

parallel · Parallel 4 turns, and none of them in a plane. A strand wrapped 4 times round a drum of radius 50 whose barrel has room for 8, with each turn lying beside the last — so the pitch is the strand's own diameter, 10 here, and the path is a helix rather than a circle. The helix angle is 1.823°, the length per turn is 314.318 against the planar model's 314.159, and the whole run is 1257.27 long where a plane would have said 1256.64. The plan view is a planar wrap exactly: projected onto the plane perpendicular to the axis, the helix is a circle of the drum's own radius to 2.8e-14 traversed 4.000000 times.

The wrap that walks along the axis

Every figure in this field is drawn in a plane, and a strand that goes round twice cannot be: the second turn has to lie beside the first. The plan view of the helix that results is a planar wrap exactly — so every wrap angle survives and the length does not, by five hundred parts per million on a real rope.

strands · Strand Three joints, and the three screws that describe them. A leg of three revolute joints, drawn as its three axes, and the principal screws of the three-system they span, drawn through the system's own centre. The three principal axes are mutually perpendicular — worst cosine 1.1e-16 — and they meet at one point, missing it by 2.6e-16. Their pitches are -0.3766, -0.0338, 0.8075, and every screw the leg leaves free has a pitch the three of them give by h₁l² + h₂m² + h₃n². Nothing in the three joint axes looks like a right angle and the system's own frame is one.

What a leg of three joints leaves free

Five essays of this field have computed the order of a screw system and drawn none of them. A three-joint leg spans a three-system; its three principal axes are mutually perpendicular and meet at a point, six numbers price every screw in the family, and the directions of the lines it contains form a cone.

spatial · Spatial What a leg of three joints permits and what it resists, on one frame. The leg of three revolute joints in grey, and the principal screws of two three-systems drawn through one centre: the twists the leg lets its platform make, and the wrenches it holds without any joint turning. They are computed separately — the second is the reciprocal complement of the first, found by its own eigenproblem — and they come out with the same centre, 5e-16 apart, and the same three axes, parallel to 0e+0. Only the pitches differ, and each wrench pitch is its twist's with the sign reversed, to 1e-15: -0.3766 against 0.3766, -0.0338 against 0.0338, 0.8075 against -0.8075.

The lines a leg turns about and the lines it is pushed along

A leg of three revolute joints permits a three-system of motions and resists a three-system of loads. The two share a centre and three axes and differ only in the sign of every pitch — and the revolute axes of the first and the lines of force of the second are the two rulings of one hyperboloid, every line of one meeting every line of the other.

spatial · Spatial A paired platform with its pairs rotated 60°, turned through a revolution. The paired Gough platform — base anchors in pairs 25° apart on a radius of 2.2, platform anchors in pairs 40° apart on 1.1 — with the platform's pairs centred 60° round from the base's, held level and turned through a revolution at four positions. All four curves reach nought together at 30° and −150°, which is 90° − ρ and 180° from it. At the centred position the platform is held at 0.0363 at a yaw of 0°, and it can turn ±17° before that falls to half. Dragging the rotation carries the two dead yaws across the revolution together.

The dead yaw is a design choice

A paired hexapod held level is singular everywhere at a yaw of 30° because its platform pairs sit 60° round from its base pairs. Rotate them by ρ instead and the dead yaws move to 90° − ρ and 180° from it, exactly, at every rotation from 0° to 120°. The furthest they can be from home is a quarter-turn each way, at ρ = 0 — where the platform is also best held at home and can turn ±75.5° before its holding halves, against ±17° for the usual 60°.

parallel · Parallel

Named alongside it

The objects these essays reach for when they reach for this one.

ScrewConstraintBase circleDisplacement subgroupPressure angleTwistDegrees of freedomLower pairRatioReciprocal screwCoupleInvolute

All concepts