Machine Kinematics
solved, then drawn
Concept

Coupler curve — where it appears

The path traced by a point of a four-bar's coupler, a sextic in general and the object a coupler-curve atlas was a catalogue of. Its degree is why choosing the linkage that draws a wanted curve is hard, and why atlases of them were printed and sold before anybody could compute one.

Named by 31 essays across 11 fields — each of them below, with the objects they name alongside it.

What the machine draws, against where the polynomial vanishes. Two objects, found two ways. The thin line is the set where x^4 + 2x^2y^2 + y^4 − 1.2x^2 + 1.2y^2 is zero, walked over a grid with no mechanism involved. The marks are where the compiled machine's tracing point went, one per converged solve, over the 147 positions of its working arc. The machine's constraint set never mentions the polynomial, so evaluating it at each traced point is an independent check: the worst value over the whole arc is 3.7e-13. The arc is 1.30 radians of the driving angle and not the whole turn, and past that arc it draws something else.

A demand that is an equation

Every field on this site is handed its demand geometrically — three positions, a sampled path, a ratio at each angle — and hands back a mechanism that is right at those places and approximately right between them. This one is handed a polynomial, and the mechanism that comes back satisfies it everywhere it moves.

computing · Compute Three prescribed positions of a rigid body. The whole of the design problem, before any mechanism exists. A body has to occupy these three positions — each one a place and an angle, three numbers — and what carries it between them is not yet decided. A forward analysis starts from link lengths and finds the motion. This starts from the motion, and the lengths are what has to be found. The marked points are the poles: any planar displacement is a rotation about one point, so each pair of poses has one, and the arcs show the turn each represents through the body's own origin. A pole is a property of the displacement and not a mechanism — nothing has been chosen yet. 1 of the 3 poles lies outside this frame and is not drawn; near-parallel displacements push their pole a long way off.

The problem the other way round

Every essay before this one starts from link lengths and finds the motion. That is the reader's problem, because lengths are what a drawing shows. It is not the designer's problem, which is the reverse — and the reverse is hard enough that for a century the practical method was to look the answer up in a book.

synthesis · Synthesis Five points on one coupler. The same four-bar, with a tracing point rigidly attached to the coupler at five different places. Each curve is a sextic — degree six — and moving the attachment point a little changes it a great deal. That sensitivity is the reason coupler-curve synthesis was done with atlases of printed curves for most of the twentieth century: there is no simple inverse, so the practical method was to look one up.

What a coupler point draws

A point rigidly attached to the coupler of a four-bar traces a curve of degree six. Move the attachment a little and the curve changes a great deal. For most of the twentieth century the practical way to find the linkage that draws a wanted curve was to look it up in a book of printed atlases.

curves · Coupler Same links, same pins, different chains. Watt chain on the left and Stephenson chain on the right. They have the same number of links, the same number of pins and the same assortment — 4×2 + 2×3 — so no count of anything can tell them apart. What differs is where the pins go: on the left the two ternary links share a pin, on the right they do not, and that single fact makes two mechanisms with different coupler curves, different numbers of inversions and different position problems. It is the smallest case in the subject of the thing this field exists to say: the arithmetic is a filter and the graph is the answer.

Same links, same pins, different machines

Watt's six-bar and Stephenson's have six links, seven pins, four binary links and two ternary ones. Every count anybody can make on them agrees. They are different chains, they give two mechanisms and three, and the difference is whether the two ternary links share a pin.

topology · Topology Peaucellier's cell: exact straight-line motion from pin joints. The rhombus and the two long arms hold |OP| · |OQ| constant at 16 = 5² − 3², which is inversion in a circle about O. Inversion carries circles through the centre to straight lines, and the link CQ makes Q run on exactly such a circle — so P travels on a line, with no approximation anywhere. Measured over 160 solved positions the deviation is 6.5e-16 of the span, which is arithmetic noise rather than a small error.

Peaucellier and the exact answer

Eighty years after Watt settled for an approximation, a French army officer found a linkage that draws an exactly straight line from pin joints alone. It works by inversion in a circle, the product it holds constant is measurable, and on this site it comes out straight to 10⁻¹⁶ of its span.

curves · Coupler The circle of points going straight, at 66°. Every point on this circle is, at this instant, travelling in a straight line: its path has zero curvature there. The circle passes through the pole — where the point is not moving at all — and its diameter is 47.64, which is the pole's own speed divided by the plane's angular rate. Nothing here was assumed to be a circle. The locus is the zero set of a quadratic whose |w|² coefficient is φ′³, a real number with no cross term and no difference between its two square terms, and a general conic fitted to the sampled locus returns those coefficients at 8.1e-15 and 6.4e-15. At this position the coupler is close to translating, the pole has run off the canvas and the circle with it — the figure is the size of the mechanism, and δ here is 13.6 coupler lengths. positioned by solving, not by drawing.

The circle of points going straight

At any instant some points of a moving plane are travelling in a straight line. They form a circle — not nearly a circle, a circle — and the reason is one real coefficient in a quadratic. A coupler curve has an inflection exactly when that circle sweeps over the tracing point, which turns out to be rare.

curvature · Curvature The curves that do not move. A rotation about a point carries a curve into itself if and only if the curve is an arc of a circle centred on that point, and that one sentence is every exact dwell on this site. Each bar is how far a curve moves when it is turned two degrees about the axis its mechanism turns about, as a fraction of its own radius. The two arcs about their own centres — a cam's dwell and a deadbeat's locking face — sit at the sampling floor, which is the sagitta of the polyline they are measured as and not a property of the geometry; the number is quoted with the floor beside it because an agreement quoted without its resolution is a mistake this site has already made once. Everything else is orders of magnitude above it, including the near-circular stretch of a coupler curve that a six-bar builds its approximate dwell out of.

The arc that is concentric with the pivot

A rotation carries a curve into itself exactly when the curve is an arc of a circle about the centre of rotation. Every exact dwell on this site is that one sentence applied — a cam's dwell, a Geneva's locking disc, a deadbeat escapement's locking face — and the six-bar dwell that is merely very good is what happens when the curve is nearly one.

timing · Intermittent 3 four-bars, one coupler curve. Three different four-bars, with different ground pivots, different link lengths and different proportions — 0.692 and 0.799 times the size of the first. Every one of them draws this same curve. Roberts's theorem says there are always exactly three, and the construction is one complex multiplication: write the coupler point as λ = (P − A)/(B − A), put the third fixed pivot at O₂ + λ(O₄ − O₂), and the other two linkages fall out with their bars' roles permuted — what is a coupler in one is a crank in another. The curves here were traced separately, each from its own solver runs, and agree to 1.3e-5 against a sampling resolution of 1.4e-5 — which is to say, as closely as the comparison can tell.

Three linkages, one curve

Every coupler curve is drawn by three different four-bars, not one. The other two can be constructed from the first with a single complex multiplication, they have different proportions and different ground pivots, and the roles of their bars are permuted — what is a coupler in one is a crank in another.

synthesis · Synthesis Where the coupler is pivoting, at 70°. At any instant the coupler is turning about one point — not a pin, and usually not on the mechanism at all. Kennedy's theorem finds it: the crank and coupler share the pin at A, the coupler and rocker share B, so the coupler's centre relative to the frame must lie on both O₂A extended and O₄B extended, and it is where they cross. The dashed lines are that construction. The cross is a completely different route to the same point — the place where the coupler's solved velocity field is zero, computed from the Jacobian and knowing nothing about Kennedy. Across 119 positions the two agree to 2.7e-15. At this instant the centre lies outside the frame — the two construction lines are nearly parallel, the coupler is close to translating, and the pivot has run off rather than gone missing.

Where the coupler is turning

At every instant the coupler of a four-bar is rotating about a single point — not a pin, and usually not on the mechanism at all. Track that point in two different frames and you get two curves which, rolled on each other without slipping, reproduce the coupler's motion exactly. The bars are one way of producing it and not the motion itself.

curves · Coupler The wheel is the coupler — double wishbone. The suspension solved at 0 mm of bump, with the whole travel ghosted behind it. The two arms are the cranks and the upright between them is the coupler; the wheel is bolted to that coupler, so camber is the coupler's rotation and nothing else. Camber here is 0.00° and the contact patch has moved 0.0 mm across the road. The cross is the instantaneous centre of the upright, found from the solved velocity field; the roll centre is where the line from it to the contact patch crosses the car's centreline, and it is at 73 mm here.

The wheel is the coupler

A double wishbone is a four-bar standing on end whose coupler carries a wheel, so camber is coupler rotation and scrub is a coupler point's path. Both are computable, and the second one comes out with the opposite sign from the model every suspension book uses — by more than the whole scrub.

applied · Fourbar Three linkages, one polynomial. Roberts's theorem says three different four-bars draw the same coupler curve. Here each one is traced, and each trace is fitted separately for the sextic that vanishes on it — on a common normalisation, or the comparison would be between three polynomials in three coordinate systems. The twenty-eight coefficients agree across all three to 5.0e-7. The three traces are drawn on top of one another and the curve is the same object each time; the test shares nothing with the construction that produced the cognates, which is why it is a test.

Three linkages, one equation

Roberts's theorem says three different four-bars draw the same coupler curve. Fitted separately for the sextic that vanishes on each trace, on a common normalisation, the twenty-eight coefficients agree across all three to 5 × 10⁻⁷ — a test of the theorem that shares nothing with the construction the cognates came from.

curves · Coupler A pin in a hole is a short link. Left: a pin of radius 0.86 in a hole of radius 1, so the clearance is 0.14. The pin's centre may sit anywhere within that of the hole's centre. Right: the same joint as it enters the kinematics — a binary link of fixed length 0.14 and free direction, with a revolute at each end. That is not an analogy. It is the same set of relative positions, so every count, every Jacobian and every solve on this site applies to it unchanged, and a four-bar with play at each pin is a mechanism with eight links and eight joints.

A clearance is a link

A pin in a hole is not a joint at a point. Its centre may sit anywhere within the difference of the two radii, so the two links it joins are connected by a body of fixed length and free direction — a binary link with a revolute at each end. That is not an analogy, and taking it literally makes a four-bar a mechanism with eight links, eight joints and five degrees of freedom.

practice · Clearance Two ovals of one sextic. A four-bar with ground 4, crank 1, coupler 3.5, rocker 3, its coupler point solved at 720 crank angles on each assembly. Each assembly closes on its own oval through a full turn of the crank, and the two ovals never meet: they come no closer than 1.712. Every solved point satisfies the one eliminated sextic to 6.6 × 10⁻¹⁶ of its largest term. The machine drawn solid and the one drawn faint are the same four bars at the same crank angle of 60°, and taking a pin out is the only way from one oval to the other.

The curve the other assembly draws

A crank-rocker's two assemblies do not share a coupler curve. Each draws a whole closed oval of its own through a full turn of the crank, the two ovals never meet, and both are the zero set of one sextic, so the equation a machine's own motion determines also describes a second machine it can never become.

curves · Coupler Three double points, and the one that is real is never visited. The coupler curve of a four-bar with ground 4, crank 1, coupler 3.5, rocker 3, coupler point at u = 0.45, v = 0.50, both ovals solved. The dashed circle is where the coupler's orientation can fail to be fixed by the point it carries; it passes through both fixed pivots and through the third pivot of the cognate construction, centre (2.000, 0.010), radius 2.0000. The curve's three finite double points are on it. The one that is real is isolated — a point of the curve no oval passes through, at (3.964, −0.368). The other two are a complex-conjugate pair and have no place in the plane.

A point the machine never reaches

Every coupler curve has three finite double points, and an odd number of them are real, so no coupler curve has none. On the standard crank-rocker the only real one is a point of the curve that neither assembly ever visits, that no contour plot can find, and that sits on the circle through the three pivots of Roberts's cognates.

curves · Coupler A dwell is a measurement, not a stop. The Stephenson six-bar's output against a full turn of the crank, with the four-bar it is built on for comparison. Inside a band of ±1° the six-bar's output holds still for 145.8° of crank and the four-bar's for 41.9°. The dwell comes from a stretch of the coupler curve that fits a circle of radius 3.006 to within 2.96e-3, and the arm from the coupler point is that radius. Nothing here stops; it moves less than the band.

A dwell made from a curve

Parts of a coupler curve are very nearly circular arcs. Put a link of the arc's own radius on the coupler point and its far end stands almost still while the point runs along it, so the output dwells — 146° of crank inside a one-degree band, against 42° for the four-bar it is built on. A dwell linkage does not stop. It moves less than the tolerance, and how much less is a number.

linkages · Synthesis A parallelogram's sextic is a circle and a quartic. The parallelogram with ground 4, crank 1.5, coupler 4, rocker 1.5, coupler point at u = 0.45, v = 0.50. Its eliminated sextic divided by the circle of radius 1.5000 about (1.800, 2.000) leaves a remainder of 6.3 × 10⁻¹⁶ of its largest coefficient, and the quotient is a quartic whose leading form is exactly a multiple of (x² + y²)². Of the configurations solved across a full turn on both assemblies, 720 are on the circle — the machine as a parallelogram, coupler parallel to the ground — and 720 on the quartic, the machine crossed. The two factors meet at four finite points: 2 are change points, marked solid, where one configuration belongs to both; the other 2 are places the two drawings merely cross.

A sextic that comes apart

A parallelogram chain's coupler curve is not one curve. Its sextic divides exactly by a circle, leaving a quartic, and each factor is one of the two things the machine can do. The division leaves rounding and nothing else, a coupler one millionth too long leaves a remainder a million times larger than rounding, and the two factors meet at the two places where the machine has to choose.

curves · Coupler What degree a coupler curve actually is. A four-bar's coupler point traced at 602 solved positions, then asked which polynomials vanish on those points. For each degree the design matrix's smallest singular direction is taken and its worst residual plotted. Degrees four and five leave nothing near zero; degree six drops by ten decades and degree seven buys nothing further. The textbook sentence — a coupler curve is a sextic — comes back as a measurement, and the decision is made by the gap between the smallest singular value and the next, which here is a factor of 2.8e+3 — at 15, 21, 28 and 36 monomials respectively.

The equation a four-bar satisfies

Every textbook says a coupler curve is a sextic. Traced at six hundred solved positions and fitted at degrees four through seven, the answer comes back as a measurement: nothing vanishes below six, degree six drops by ten decades, and degree seven buys nothing — with the decision made by a gap of 2.8 × 10³ rather than by a residual.

algebra · Algebra A corner in a curve, and the reason for it. This coupler point traces a curve with a cusp — a corner, where the curve stops and reverses rather than turning. The reason is that a cusp happens where the tracing point is momentarily still, and the only point of a moving plane that is momentarily still is the pole. So the cusps of a coupler curve are the instants when the pole passes through the tracing point: they are the crossings of the tracing point by the moving centrode, which is a statement about two curves in the coupler's own plane with the fixed plane not involved at all. This point was chosen by taking the pole's body coordinate at one instant, so it is on the moving centrode by construction; at the corner its speed is 9.9e-15 against 2.87 a fifth of a radian later. positioned by solving, not by drawing.

Where a curve has a corner

Some coupler curves have corners in them — points where the curve stops, turns round and comes back. A corner happens where the tracing point is momentarily still, the only point of a moving plane that is momentarily still is the pole, and so the corners of a coupler curve are decided entirely inside the coupler's own plane.

curvature · Curvature The error between the precision points. chebyshev: worst 0.2232°, RMS 0.1475°; least-squares: worst 0.3900°, RMS 0.1203°. The error is zero at each precision point by construction and nowhere else. chebyshev has the smallest maximum here, and which curve is best depends entirely on which measure is asked for.

Where an optimiser starts

An approximate synthesis is a local search on an objective that is non-convex, disconnected and not everywhere defined, so the answer depends on where the search began. Nothing in the optimisation supplies that. What supplies it is the exact constructions the field spent four rungs on, and an atlas of coupler curves — which is why a method superseded by computers is still the thing that feeds them.

synthesis · Synthesis Crank angle θ and crank angle −θ, joined. The coupler curve alone, with 12 chords, each joining the point the tracing point reaches at a crank angle θ between 0° and 180° to the point it reaches at −θ on the same assembly. Every chord is square to the dashed axis, to 7.5 × 10⁻¹⁶ in the cosine, and every midpoint lies on it. Measured at 48 pairs, the reflection of one point misses the other by at most 4.2 × 10⁻¹⁵. The crank's own angle is the pairing: the two places the curve crosses its axis are crank angles 0° and 180°, the only angles equal to their own negatives.

A symmetric curve from a lopsided machine

A four-bar with a crank of 1, a ground of 3 and a rocker of 2.5 has no symmetry anywhere in it. Make the rocker, the coupler and the arm from the rocker pin to the tracing point one length, and the curve it draws is its own mirror image to 4 × 10⁻¹⁵, about a line through the rocker pivot turned from the ground line by exactly half the coupler's angle at that pin.

curves · Coupler Two ways to stop an axle moving sideways. A Panhard rod is one link from the body to the axle, so the axle's end follows an arc and the whole car shifts sideways as the suspension moves: 3.56 mm at 80 mm of travel, and always in the same direction, so it happens twice per bounce. A Watt's linkage keeps the same point on a path that is straight to 33.7 µm — 106 times better, and it is drawn on the same axis, which is why it looks like the zero line.

Holding an axle still

A Panhard rod moves the axle 3.56 mm sideways over 80 mm of travel and a Watt's linkage moves it 34 microns — a hundred times better, and by a higher power. The Panhard's error is quadratic in the travel and the Watt's is fifth order, which is a much stronger statement than "the Watt is better" because it says how the comparison changes with the suspension.

applied · Coupler A line across the four-bar's coupler curve. The curve traced by a point on the four-bar's coupler, over every real configuration, with the machine drawn faintly at one of them. A real line crosses it at 4 marked points. Written as polynomials, the machine and the line have 8 paths to track; 6 arrive, 2 leave for infinity, and the arrivals draw 6 distinct points — 4 real and 2 complex. A random complex line gives 6 as well, which is the curve's degree.

A degree counted on a line

A curve of degree six meets a general line in six points, and that sentence is a way to measure the degree with no equation in it. Written as polynomials, a four-bar and a random complex line have eight paths to track; six arrive on every line tried, the other two run off towards the circular points, and a sum of the six stays straight to fifteen figures only when none is missing.

algebra · Algebra One crank, four machines, one area. Four crank-rockers sharing only a crank of length 1, with grounds, couplers and rockers all different, each tracing the point 30% of the way from the crank pin to the rocker pin. The curves have different shapes and sizes and different places in the plane, and the area each one encloses is 2.199115 = (1 − 0.3)·π·1² — on both assemblies of every one, with a worst difference of 3.2 × 10⁻¹⁴.

The area a coupler point encloses

Trace a point on the line through a crank-rocker's two moving pins and the region its curve encloses has area (1 − u)πa²: the crank pin's own circle, scaled by how far along the line the point sits. No ground, coupler or rocker length appears in it. Four machines that share only a crank enclose 2.199115 each, to 3 × 10⁻¹⁴.

curves · Coupler The circle of points going straight, at 66°. Every point on this circle is, at this instant, travelling in a straight line: its path has zero curvature there. The circle passes through the pole — where the point is not moving at all — and its diameter is 47.64, which is the pole's own speed divided by the plane's angular rate. Nothing here was assumed to be a circle. The locus is the zero set of a quadratic whose |w|² coefficient is φ′³, a real number with no cross term and no difference between its two square terms, and a general conic fitted to the sampled locus returns those coefficients at 8.1e-15 and 6.4e-15. At this position the coupler is close to translating, the pole has run off the canvas and the circle with it — the figure is the size of the mechanism, and δ here is 13.6 coupler lengths. positioned by solving, not by drawing.

A curvature is a size with a minus sign

Everything in the curvature field is a similarity invariant in shape and a reciprocal length in value. Scale a moving plane and its inflection circle scales, its cubic of stationary curvature scales, and every curvature it computes is divided by the factor — so a bigger machine traces gentler paths than its drawing suggests.

curvature · Curvature Three machines drawing one oval, and where each keeps its area. The crank-rocker with ground 4, crank 1, coupler 3.5 and rocker 3, its tracing point at (0.45, 0.5) of the coupler, and the two other four-bars Roberts's construction gives for the same curve, each drawn holding the same point of one oval and each with its input pin's path dashed in the input colour and its output pin's in the output colour. The shaded oval encloses 2.116354 for all three. In the crank-rocker the crank pin goes round and carries 1.727876 of it; in the double rocker neither pin goes round and the coupler's turn carries 1.727876; in the rocker-crank the output pin goes round and carries 1.727876. The remaining 0.388478 is the same in all three.

Where three machines keep one area

Roberts's theorem gives every four-bar two others that draw the same coupler curve, and so enclose the same areas. Measured, they do, to 10⁻¹² — but each keeps the area in a different place: the crank-rocker in its crank pin's circle, the double rocker in its coupler's turn, the third machine in its output pin's circle. What is left over has no closed form, and it is one number in all three.

curves · Coupler A dwell six-bar built on the vertex of a symmetric coupler curve. The four-bar with ground 3, crank 1, and coupler, rocker and arm all 2.5, with the angle at the rocker pin set to 120.8024°, so that its coupler curve is its own mirror image about the dashed line. The curve crosses that line at crank angle 0°, and a link of the osculating radius there, 5.7691, runs from the tracing point to a pin at the centre of curvature; an output link of 3 from a third ground pivot holds that pin, square to the dwell link at the vertex. Faintly, the dwell link and output 50° of crank either side. The output swings 7.43° over a whole turn, and near the vertex its angle changes only at sixth order in the crank's.

The flattest dwell is not the longest

A coupler curve that is its own mirror image has no odd terms in its distance from a circle centred on the mirror line, so one angle of the coupler can remove the fourth-order term and leave a dwell of sixth order, with no search of the curve. A six-bar built there dwells for 58.7° of crank inside 0.1% of its swing. Turned two degrees away from that angle it dwells for 80.1°, and the searched six-bar for 24.4°.

curves · Coupler Where a fit's singular values fall away, on each motion of a parallelogram. The 28 singular values of the degree-six fit, largest first and relative to the largest, for points traced on the parallelogram's circle motion, on its quartic motion, and on both. On the circle motion the last 15 lie below a drop of 3.7 × 10¹³, from 0.232 to 6.2 × 10⁻¹⁵; on the quartic motion the last 6 lie below a drop of 3.0 × 10¹⁰, from 6.3 × 10⁻⁵ to 2.1 × 10⁻¹⁵; on both motions the last one lies below a drop of 2.5 × 10¹², from 3.1 × 10⁻⁴ to 1.2 × 10⁻¹⁶. A drop of ten decades or more is a null space that is exactly there: fifteen sextics vanish on a circle, six on a quartic, and one on both.

A null space of fifteen is not noise

Points traced on one motion of a parallelogram four-bar leave a degree-six fit with fifteen polynomials that vanish on them, behind a drop of thirteen decades: the circle times every quartic. Half an oval of an ordinary coupler curve leaves two to five, behind drops of two. The count is the same kind of number in both cases, and only the drop beside it says which one is algebra.

curves · Coupler What region each four-bar's two cognates land in. One row per region of length space. Against each, the regions of the two four-bars Roberts's construction gives for the same coupler curve, and how many of the 24000 chains in the census landed in that region. Every row has one entry: across the whole census, and at each of 5 tracing points, the original's region decides its cognates' regions with nothing left over. The four Grashof regions are above the rule and the four triple rockers below it, and no row crosses it — a crank-rocker has a double rocker and a rocker-crank, a double crank has a double crank and a double crank, a rocker-crank has a rocker-crank and a double rocker, a double rocker has a crank-rocker and a crank-rocker, a 0–π rocker has a 0–π rocker and a 0–π rocker, a π–π rocker has a π–π rocker and a π–0 rocker, a π–0 rocker has a 0–0 rocker and a 0–0 rocker, a 0–0 rocker has a π–0 rocker and a π–π rocker.

The kind is decided before the lengths are

Roberts's construction hands a four-bar two others that draw its curve, and which of the eight kinds those two are is settled by the kind of the first — not by its lengths within that kind, and not by where the tracing point sits. Twenty-four thousand chains at five tracing points produce no exception, and the reason is one line: the tracing point enters the construction only as a scale, and a region is scale-blind.

curves · Coupler The same five-bar with its gears meshed outside and inside. A geared five-bar drawn over a whole cycle at four ratios, with its two cranks turning against each other in the top row and together in the bottom one — an external mesh and an internal one, which is the same machine with the ratio's sign changed. Both assembly branches are drawn. The curves have the same degree in both rows — 1 : 1 at 6, 2 : 1 at 10, 3 : 2 at 16, 5 : 3 at 26 — and they are not the same curves: the lower ones are the maximally circular members of their degree and the upper ones are not, which is a difference nothing about the drawing shows.

The mesh inside keeps the half

Mesh a geared five-bar's two gears inside each other instead of side by side and the cranks turn together rather than against each other. The curve its pin draws has exactly the same degree at every rational ratio — and it passes through each circular point half that degree, which is as often as any curve can, where the counter-rotating machine manages between a third and two fifths. The sign of the ratio is the whole difference.

algebra · Algebra Three machines, one curve. The coupler curve of a four-bar, drawn three times by three different linkages. Roberts's theorem gives every coupler curve exactly three four-bars that trace it, and their proportions are not close: the cranks here are 1.600, 2.214, 2.558, a spread of 60%. Read as an identification problem this is a least-squares objective with three separate exact minima and nothing between them — so an instrument that records only where the tracing point went has three answers however good it is, and no amount of data chooses. What chooses is knowing where the ground pivots are, which is a different measurement rather than a better one.

Three machines, one curve

Roberts's theorem says every four-bar coupler curve is drawn by exactly three different four-bars. Read as an identification problem that is a least-squares objective with three separate exact minima, whose cranks differ by sixty per cent — so an instrument that records only where the tracing point went has three answers, and no amount of data chooses between them.

metrology · Parameter Three laws in the band: a third, a sixth and a sixth. For bands from 3% to 10 ppm of the output's swing, three things measured on the symmetric six-bar itself: the longest dwell at any angle at the rocker pin, the dwell at the sixth-order angle γ = 120.8024°, and how far below γ the best angle sits. The dots are measurements and the lines are the two-term model's predictions from two coefficients read off the output's even part. Over the four tightest bands the fitted exponents are 0.173, 0.172 and 0.333, against a sixth, a sixth and a third. At 10 ppm the best angle is 0.490° below γ against a prediction of 0.488°, and the dwell at γ is 26.43° against 26.23°. The loosest bands sit above the lines, where the terms the model leaves out are no longer small.

The dip that buys the dwell

A symmetric coupler curve's six-bar dwells longest a little below the angle that makes its error sixth order, and three bands gave three numbers. Across three and a half decades of tolerance the best angle's distance from that angle grows as the cube root of the band, both dwells as its sixth root, and their ratio is (27/4)^(1/6) = 1.3747 at every band — because the best machine spends the whole band on one dip and ends its dwell where the output comes back.

curves · Coupler

Named alongside it

The objects these essays reach for when they reach for this one.

Cognate linkageImplicit equationSexticAlgebraic curveAssembly branchConstraintDwellthe Roberts–Chebyshev theoremCrank-rockerDegreeDouble pointGrashof's condition

All concepts