Machine Kinematics
solved, then drawn
Concept

Harmonic — where it appears

Following a sinusoid in the driving parameter, as a motion law or as a component of one. A harmonic cam law is smoother than a parabolic one and rougher than a cycloidal one, and its peak acceleration sits between theirs.

Named by 4 essays across 4 fields — each of them below, with the objects they name alongside it.

A ratio that is not a number. The output-to-input angular velocity of a four-bar, computed from the velocity solution at every position. It runs from -0.398 to 0.333 — it changes sign, because the rocker turns back — with a mean of 0.000 that no instant of the cycle actually exhibits. Quoting a single figure for a linkage's ratio is quoting the average of that curve. A gear pair is the case where the same phrase is honest: its ratio is 0.5000 and stays there, which is not a coincidence but the property the involute was invented to guarantee.

The ratio that is not a number

A four-bar's output-to-input speed ratio runs from −0.29 to 0.51 through one turn and changes sign on the way. Quoting a single figure for it quotes the average of that curve, which the mechanism never exhibits. A gear pair is the case where the same phrase is honest, and it is honest by construction.

wrong · Misconception The same rise, three ways. A 20-unit rise over 120°, then a dwell. Above, the displacement — all three do the same job and are hard to tell apart. Below, the acceleration, differentiated from those same curves. Constant acceleration peaks lowest at 5.556e-3 per degree² and arrives at the dwell with a step; cycloidal peaks highest at 8.727e-3 and arrives at zero. The smoothest law has the largest peak, which is the trade the whole of cam design turns on and which the displacement plot gives no hint of.

The law that costs least is not the smoothest

Constant acceleration gives the lowest peak acceleration of any motion law and an impulsive jerk. Cycloidal motion has finite jerk everywhere and a peak acceleration 57% higher. The trade is real, it is measurable, and the displacement curves that everyone plots give no hint of it.

cams · Cam Slider-crank at 50°. Crank 1, connecting rod 3. The slider's travel is 2.0000 — exactly twice the crank throw, which is the one thing about this mechanism that does not depend on the rod length. Everything else does: the rod length decides how far the piston's motion departs from a sine wave, and that departure is the second harmonic every engine balancer has to deal with.

The slider-crank

Replace one pin of a four-bar with a slide and you get the mechanism in every reciprocating engine ever built. Its stroke is exactly twice the crank throw and does not depend on the connecting rod at all. Everything else about the motion depends on the rod, including the part that is always described as a sine wave and is not.

linkages · Fourbar One shaft angle, five places along a twisted rotor. A mismatched pair — a cycloidal rotor against a circular-tipped one of the same height, which are not each other's conjugates — with the rotors twisted by 1 lobe pitch along their length. The section at a given place along the shaft is the flat pair at an input angle shifted by the twist so far, so at one instant the five sections shown are at five different phases of the same mesh: the two bodies are into each other by 2.42 at the tightest section and 2.34 apart at the widest, with a mean of -0.408 across the whole seal. All five are drawn at one scale, and nothing here is meshed twice: one planar profile is read along a window.

A twist steadies what it cannot tighten

A helical rotor's sections are at different phases of the same mesh, so the clearance a machine has at one instant is a window along its own profile rather than a point on it. A wrap of exactly one lobe pitch holds the seal's open area constant through the turn — every harmonic at once, whatever the profile — and leaves its average, its tightest place and its widest place exactly where they were.

meshing · Meshing

Named alongside it

The objects these essays reach for when they reach for this one.

ConstraintAccelerationRatioStrokeAverageClearanceConjugate-actionContact ratiocycloidal motionDead centreDesign ruleDwell

All concepts