Machine Kinematics
solved, then drawn
Concept

Pitch curve — where it appears

The curve that rolls without slipping on its mate, and the locus of the pitch point in one body's own frame. For a circular pair it is the pitch circle; for a demanded varying ratio it is whatever the demand forces it to be.

Named by 7 essays across 2 fields — each of them below, with the objects they name alongside it.

A cycloidal cam at 60°. A 20-unit rise over 120°, a dwell, a return and a dwell. The dashed curve is the pitch curve — where the roller's centre travels — and the solid one is the surface that has to be cut, which is the pitch curve offset inward by the roller radius along its own normal. The pressure angle at this instant is 25.5°: the angle between the follower's direction of travel and the normal to the surface, and the number that decides whether the follower jams in its guide rather than sliding.

Prescribing motion

A linkage gives the motion its geometry allows. A cam gives the motion it was asked for, which sounds like an improvement and is a trade — the displacement becomes free and the derivatives stop being.

cams · Cam A 34-unit roller on a 20-unit base: the cam cannot be made. The outer curve is the pitch curve — where the roller's centre has to go, which is just the base radius plus the follower's displacement, plotted in polar coordinates. The inner curve is what has to be cut: the pitch curve offset inward by the roller's radius along its own normal. Where the pitch curve bends more tightly than the roller is wide, that offset crosses itself, and the metal the profile needs has already been removed. The tightest radius of curvature here is 19.43 at 85°, against a roller of 34 — so the cam is undercut by 14.57 and no amount of care in manufacture recovers it. The pressure angle, meanwhile, peaks at a perfectly comfortable 21.2°: this cam fails a test it never looked like failing.

The cam that cannot be cut

A cam has to be big enough for two reasons, and they are not the same reason. One is that the follower will jam in its guide if the pressure angle is steep. The other is that the roller will gouge the profile if the curvature is tight — and there is a combination where the pressure angle is comfortable and the cam still cannot be manufactured at all.

cams · Cam A cam is the envelope of a roller. The follower's roller drawn in the cam's frame at 15 angles of the cam: the roller slides in a straight guide and the cam turns under it, so from the cam's point of view the roller travels round it on a path set by the lift law. The cam's surface is the envelope of those circles — the same computation as a rack generating a tooth, with a circle instead of a straight edge and a lift law instead of a rolling condition. The cams field builds the same surface by offsetting the roller-centre path inward by the roller radius, and the two agree to 4.1e-4 mm. positioned by solving, not by drawing.

A cam is a conjugate pair

A cam is built by offsetting the path of the follower's centre inward by the roller radius. It can also be built by asking what shape stays in contact with a circle that slides in a stated way — the same computation that cuts a gear tooth — and the two surfaces agree to sixteen millionths of a millimetre.

cams · Cam Two ellipses on their foci, at a ratio of 0.603. Each wheel is an ellipse turning about one of its own foci, with the centres a major axis apart. The focal property does the work: the two radii from the two foci add to the major axis, so the contact stays on the line of centres by construction, and the rolled arc lengths agree to 2.5e-8 of their length. The ratio at this instant is 0.6033; over a turn it runs from 0.538 to 1.857, a range of 3.4490 against the ((1+e)/(1−e))² = 3.4490 the eccentricity predicts. And one turn of one wheel is exactly one turn of the other, which is the condition that makes it a pair of wheels rather than a pair of curves. positioned by solving, not by drawing.

A ratio that is a function of the angle

A gear pair is usually two circles rolling. Ask instead for an output that runs forty per cent fast for half a turn and forty per cent slow for the other half, and the two shapes that deliver it are not a design decision — the demand fixes both pitch curves completely, and the only question left is whether they close.

meshing · Meshing One member of the family is a pair of wheels. The same demand — one plus 0.4 sin φ — scaled by a constant, and for each the angle the driven wheel is out by after one turn of the input. It has to be zero, or the teeth do not line up with themselves and there is no wheel. Only the unscaled member closes; five per cent either way leaves the output 18° out, which is a third of a tooth on a thirty-tooth wheel and a mechanism that seizes on its second turn. Non-circular gearing is a search rather than a drawing for exactly this reason: the closure condition is one equation on a whole function, and almost no function satisfies it.

The demand that cannot be met

Ask for an output rate and the two pitch curves follow with no design step in between — so the interesting question is not how to draw them but which demands admit any pair of wheels at all. The answer is one equation on a whole function, it is about the demand's mean and nothing else, and five per cent of error leaves the output eighteen degrees out after a turn.

meshing · Meshing A roller offset by 5.88, at 42.3° of the rise. The cycloidal programme — rise 20 over 90°, return over 170° — on a prime circle of 40 with a roller of 10, drawn with the follower fixed above and the cam turned anticlockwise to 42.3°. The follower's line of travel is 5.88 to the right of the cam's centre. The contact normal leans 21.81° from that line, which is the pressure angle, and measured off the drawn pitch curve it is 21.81°. At this offset the peak on the rise is 21.81° and on the return 21.81°; centred, they are 27.37° and 15.33°.

An offset trades the rise for the return

Moving a roller follower's line of travel off the cam's centre lowers the pressure angle on one stroke by raising it on the other. When the rise and the return are mirror images the best offset is zero. When the cam rises in 90° and returns over 170°, an offset of 5.88 takes the worse stroke from 27.37° to 21.81° by handing the return 6.48° it did not need.

cams · Cam A roller on an arm of 50 pivoted on the left, at 35.8° of the rise. The cycloidal programme — rise 20 over 90°, return over 170° — on a prime circle of 40 with a roller of 10, followed by a roller on an arm of 50 whose pivot is on the left of the cam, at (−49.92, 42.79). The pivot angle balances the two strokes, and the cam is turned anticlockwise to 35.8°. The faint arc is the path the roller's centre swings through. The contact normal leans 23.48° from the roller's direction of motion, which is the pressure angle, and off the drawn pitch curve it is 23.48°. At this instant the roller's line of motion passes 2.98 from the cam's centre. Balanced, the arm peaks at 23.48° on both strokes; a sliding follower at its best offset of 5.88 peaks at 21.81°.

An arm is an offset that grows with the lift

Carry a cam's roller on a swinging arm instead of a slide and its pressure angle obeys the offset follower's formula exactly, with the offset replaced by the distance of the roller's line of motion from the cam's centre. That distance turns with the arm. On a cam whose strokes are mirror images the best arm is worse than a centred slide by about 5,000/L² degrees and leans the follower by its own tilt on the dwells. On a quick-rise cam the pivot's angle rebalances either side of the cam for under a degree, where a sliding offset moved to the wrong side costs eleven.

cams · Cam

Named alongside it

The objects these essays reach for when they reach for this one.

Pressure angleDwellCamConjugate-actionMeshing equationRoller followerUndercuttingAccelerationBase circleCam profileContact normalDescribing circle

All concepts