Machine Kinematics
solved, then drawn
Concept

Trochoid — where it appears

The path of a point rigidly attached to a rolling body, at a radius that need not be the rolling radius. A gear's root fillet is one, a rotary engine's housing is one, and neither is the circular arc drawings usually show.

Named by 4 essays across 2 fields — each of them below, with the objects they name alongside it.

A straight edge cutting a 24-tooth wheel. The rack's flanks are straight lines and its pitch line rolls on the wheel's pitch circle without slipping — 48 mm of travel per radian, which is the only number in the whole process. The dots are the contacts the meshing equation has returned so far, and they are the flank being cut: an involute, produced by a tool that has no curve anywhere on it. The corner of the rack traces the fillet below, which is a different curve for a different reason — a corner is a point, and a point has no envelope but its own path. positioned by solving, not by drawing.

The tool is the definition

There is no curve anywhere on the cutter that makes an involute gear. It is a straight edge, dragged past a turning blank, and the involute is what the motion leaves behind — along with a fillet that is a corner's path, a contact locus that comes out a straight line, and a base circle that is measured rather than drawn.

meshing · Meshing A rotor that was not drawn, at 52° of shaft. The housing is an epitrochoid — the only shape here that was written down — and the rotor is the envelope of it, seen from a body that turns at a third of the shaft's rate about a centre orbiting at the eccentricity. Nothing about the rotor was chosen. Its three apexes come out at radius 100.000000, which is the generating radius R exactly, at 0° and ±120°; the middle of each flank comes closest to the centre at 72.0000, which is R − 2e. The apexes are the only part of the rotor that touches the housing, which is why a rotary engine's sealing problem is three lines rather than a ring. positioned by solving, not by drawing.

A rotor nobody drew

The rotor of a rotary engine has three corners, three flanks and one job: to stay in contact with a housing while turning at a third of the shaft's speed about a centre that orbits. Given the housing and that motion, the rotor is not designed. It is computed, corners and all, by the routine that cuts a gear tooth.

meshing · Meshing The rotor is not a Reuleaux triangle. The generated rotor, with the Reuleaux triangle through the same three apexes drawn over it — three circular arcs, each centred on the opposite corner. They part company by 1.21 mm on a rotor of generating radius 100, and the flank is the one that is right: it is the envelope of the housing, and a Reuleaux flank would foul the wall. The measurement that cannot be argued with is the width. A Reuleaux triangle has the same width in every direction — that is what it is for — and this rotor's runs from 150.0 to 174.1, a spread of 16 per cent. positioned by solving, not by drawing.

Six things a shape is not

A rotor that is not a Reuleaux triangle, teeth that are not the same shape as each other, a fillet that is not an arc, a mesh that does not roll, a conjugate pair that cannot be built and a tooth form that was not deduced. Six claims in circulation, each with the number that kills it.

wrong · Misconception What is left of a 12-tooth flank. The flank the rack generated on a 12-tooth wheel, with every point tested against the cutter at every other position of the cut. The pale dots survive; the dark ones are inside the cutter at some later instant and are not on the finished tooth — 39 of 203 of them, the deepest by 5.19e-2 mm. Undercutting is not a shape, it is a removal: the same corner that leaves the fillet comes back for flank the straight edge had already generated, and what is lost is the part of the involute nearest the base circle, which is exactly the part the mating wheel's tip needs. Drag to change the tooth count. positioned by solving, not by drawing.

The cutter takes back the tooth

Undercutting is usually explained as a shape: a tooth with a waist in it. It is better understood as an event — the corner that leaves the fillet comes back through flank the straight edge has already generated — and seen that way the threshold at seventeen teeth is a comparison of two measured points that passes through zero.

meshing · Meshing

Named alongside it

The objects these essays reach for when they reach for this one.

EnvelopeMeshing equationConjugate-actionInvoluteBase circleEpitrochoidGenerating rackLine of actionPitch pointUndercuttingApexCusp

All concepts