Machine Kinematics
solved, then drawn
Concept

Undercut — where it appears

The part of a tooth flank a cutter has removed after generating it, leaving the tooth waisted near its root. It is not missing material but material that was made and then taken back, by the same tool later in the same cut.

Named by 6 essays across 3 fields — each of them below, with the objects they name alongside it.

A cam profile is an envelope, and its curvature obeys the same law. The dashed curve is the pitch curve — where the roller's centre travels — and the solid one is the surface that has to be cut, which is the pitch curve offset inward by the roller radius. That offset is the conjugate law of this field with one centre of curvature sent to infinity, and it says ρ_cut = ρ_pitch − r. Measured off the drawn polyline at six angles, the worst departure is 4.8e-7: at 95° the pitch curve has radius 29.52 and the cut profile 21.52, against 21.52 predicted. It is also why undercutting is a curvature condition rather than an accident: where ρ_pitch falls below the roller radius the offset turns itself inside out.

A profile is an envelope

A cam's surface is not a curve somebody drew. It is the envelope of the roller as the roller runs round the pitch curve, and its curvature is the pitch curve's less the roller radius — a law that the cam calculations here were breaking for six months, in the one curve that gets manufactured and the only one no check looked at.

cams · Cam A cycloidal cam at 60°. A 20-unit rise over 120°, a dwell, a return and a dwell. The dashed curve is the pitch curve — where the roller's centre travels — and the solid one is the surface that has to be cut, which is the pitch curve offset inward by the roller radius along its own normal. The pressure angle at this instant is 25.5°: the angle between the follower's direction of travel and the normal to the surface, and the number that decides whether the follower jams in its guide rather than sliding.

A lift is a size and a law is a shape

A cam's motion law is a dimensionless function of a dimensionless argument, so everything the cam field says about laws — which has the least acceleration, which has an impulsive jerk, which one costs least — transfers between cams of any size. What does not transfer is anything with the lift or the base circle in it.

cams · Cam The string is the radius. An involute is generated by unwinding a taut string from the base circle, and the taut string is the flank's normal — so the point where it leaves the base circle is the centre of curvature and the string's length is the radius. At a flank radius r that length is √(r² − r_b²), and the dashed curve is that expression. The dots are the curvature of the polyline this site actually draws, measured by circumcircle through consecutive points, over 324 of them. Worst relative disagreement 1.9e-6. At the base circle the radius of curvature is zero, which is why a flank cut below it is not an involute and why undercutting removes exactly that part.

Two flanks, one law

At a gear mesh the two tooth flanks are conjugate profiles, the pitch point is the pole of their relative motion, and their radii of curvature are tied to each other rather than free. Each flank's radius varies fourfold across the mesh and the sum of the two does not vary at all.

gears · Tooth The same drive with a smaller eccentric: every pin touches. Twelve pins on a ring of 60, pin radius 5, and the disc exactly as those pins generate it, at 10° of the eccentric. Left, the eccentric at exactly R/N = 5, whose roots are round sockets: 9 pins touch (solid) and 3 stand clear (dashed), the pins near the roots. Right, the eccentric at 0.8 of that, 4.00, whose roots are smooth: 12 of twelve touch. Over a pin pitch the socketed disc touches 9 or 10, and every smaller eccentric measured touches all twelve.

A disc whose roots are not sockets

Put a cycloidal drive's eccentric at exactly the pin circle's radius over the pin count and every root of its disc is a round socket; take any smaller eccentric and the roots are smooth. The sockets looked like a benefit — a pin in one closes its gap both ways at up to the full pitch offset. Measured from a half of that eccentric to all of it, they are the opposite. The socketed disc touches nine or ten of its twelve pins, every smaller one touches all twelve, and its first contact keeps the smallest share of the pitch offset of the seven. What a smaller eccentric really costs is the pitch offset itself: the free turn per unit of clearance is 0.0365 divided by the eccentric's share.

meshing · Meshing The flank bends towards the disc, and the pin's radius is measured against that bend. One root of a twelve-pin cycloidal drive, pin radius 5 on a ring of 60, with the eccentric at 0.97 of R/N. The thin line is the curve the pin's centre traces in the disc's frame, its tip pointing at the disc's centre; the dashed line is that curve offset towards the disc by the pin's radius, which is the disc's edge wherever nothing trims it. Either side of the tip the flank bends the other way, towards the disc, most tightly 22.6° of the eccentric from the root, with a radius of 5.36 (the circle, centre marked). The pin's radius, 5, is measured along the same normal to the offset point. The offset point stops short of the centre of curvature, so the offset does not fold and the root is untrimmed. The two meet at 0.9740 of R/N.

The flank that trims the root

A cycloidal disc's roots are trimmed, and its pins start standing clear, above an eccentric that was known only for one drive: 0.974 of the pin circle's radius over the pin count, for twelve pins of radius 5 on a ring of 60. The trimming is a bend. Either side of each root the flank of the pin's path curves towards the disc, and where that bend is tighter than the pin the offset folds. The bend has a closed form, so the threshold does too, √(1 − ρ²(N + 1)³/27(N − 1)) for pins of radius ρ, and it falls well below one for fat pins or many of them. On every drive measured, the classical eccentric loses contacts and lever together.

meshing · Meshing Near its threshold, the disc's flank sharpens to a point under the pin. One root of a twelve-pin cycloidal disc, pins of radius 5 on a ring of 60, cut with the eccentric at 0.97 of the threshold 0.9740 R/N. The line is the disc's edge; the circle is a pin touching it at the flank's sharpest point, 31.0° of the eccentric from the root. There the edge bulges towards the pin with a radius of 2.23, the flank's bend 7.23 less the pin's 5 (small circle, centre marked), so the contact is convex against convex, and a line contact's pressure per unit load there is 1.80 times a pin on a flat. At the root itself the edge is a hollow round the pin.

A disc cut at its threshold grows a point

A cycloidal disc's roots stay untrimmed up to an eccentric where the pin path's flank bends with the pin's own radius, and it looked as though a disc cut exactly there would have its most conformal contact, the pin and the flank sharing a curvature. It has its least. The disc's edge is the path offset inwards by the pin's radius, so where the path bends round a centre on the disc's side the edge bulges towards the pin with the path's radius less the pin's: at the threshold, a point. A line contact's pressure per unit load there rises as the inverse square root of the distance to the threshold, and the pins passing it are carrying load. Each of four drives has an eccentric of least contact stress at 0.67 to 0.80 of its threshold; cut at 0.97, the peak pressure is 9% to 80% higher for a lever 21% to 46% longer.

meshing · Meshing

Named alongside it

The objects these essays reach for when they reach for this one.

EnvelopeContact normalCycloidal drivePitch pointBacklashClearanceConjugate pointEuler savaryOsculating circlePath curvatureBase circleCam profile

All concepts