Machine Kinematics
solved, then drawn
Concept

the Geneva mechanism — where it appears

An indexing drive in which a pin on a rotating crank enters a radial slot in a driven wheel, carries it through one index and leaves. The slot count fixes the index angle and the fraction of the turn spent moving, and the tangential entry is what makes the driven wheel start and stop without a jump in speed.

Named by 11 essays across 3 fields — each of them below, with the objects they name alongside it.

A cycloidal cam at 60°. A 20-unit rise over 120°, a dwell, a return and a dwell. The dashed curve is the pitch curve — where the roller's centre travels — and the solid one is the surface that has to be cut, which is the pitch curve offset inward by the roller radius along its own normal. The pressure angle at this instant is 25.5°: the angle between the follower's direction of travel and the normal to the surface, and the number that decides whether the follower jams in its guide rather than sliding.

Prescribing motion

A linkage gives the motion its geometry allows. A cam gives the motion it was asked for, which sounds like an improvement and is a trade — the displacement becomes free and the derivatives stop being.

cams · Cam Every way of stopping, on the same four questions. Six mechanisms that all turn a continuous input into an output that moves and then waits. Index is how far the output steps. Moving is the fraction of the input's turn the output is actually going for; the rest is dwell. From rest says whether the output starts and stops at zero velocity, and acceleration whether its acceleration is a number at all. Every entry is computed from the mechanism's own library, which matters for two of them: a Geneva's moving fraction is (n − 2)/2n and not 1/n, and its entry rate is zero in closed form rather than to the accuracy of a sampled sweep. The three rows whose acceleration is not a number are not badly made — they are mechanisms whose output velocity has a step, and no tolerance improves that.

The mechanism that waits

Every mechanism in this collection so far moves whenever its input moves. A ratchet, an indexer and an escapement do not: they are still for most of a turn and moving for the rest, and what decides which is not an equation running out of answers but a tooth arriving at a face.

timing · Intermittent A 6-slot Geneva wheel. The driving pin enters a radial slot, carries the wheel through 60°, and leaves. The centre distance is not free: it must be crank ÷ sin(180°/6) = 60.00 so that the pin enters along the slot, with the crank and slot perpendicular. That is the mechanism's one design requirement and it is what makes the driven wheel start and stop from rest — measured here at 1.5e-3 against a peak of 1.000. What it does not fix is the acceleration, which peaks at 1.35 and is why film sprocket holes tear.

Stopping thirty times a second

A Geneva wheel turns continuous rotation into steps, and its one design requirement is that the pin enters the slot along the slot so the driven wheel starts and stops from rest. That fixes every dimension from the slot count. What it does not fix is the acceleration, which is why film sprocket holes tear.

cams · Cam Lost motion on a 24-tooth ratchet. A pawl can only drop into a tooth, so an input that has moved by less than one tooth pitch has moved the output by nothing at all. On 24 teeth the pitch is 15.0°, and that is the worst case with one pawl. Two pawls offset by half a pitch halve it and three thirds it, because whichever pawl is over a root drops first. None of this is a manufacturing question: the numbers are the same on a perfectly made ratchet, which is what separates them from the lost motion an as-built measurement would.

The resolution is the pitch

A ratchet's step and a ratchet's error are the same number. Nothing about how well it is made improves that, more pawls divide it by a whole number, and the obvious remedy — cut more teeth — runs into a wall that is geometric rather than practical: at a tooth depth of 0.16 radii the construction stops at twenty-nine.

timing · Intermittent The curves that do not move. A rotation about a point carries a curve into itself if and only if the curve is an arc of a circle centred on that point, and that one sentence is every exact dwell on this site. Each bar is how far a curve moves when it is turned two degrees about the axis its mechanism turns about, as a fraction of its own radius. The two arcs about their own centres — a cam's dwell and a deadbeat's locking face — sit at the sampling floor, which is the sagitta of the polyline they are measured as and not a property of the geometry; the number is quoted with the floor beside it because an agreement quoted without its resolution is a mistake this site has already made once. Everything else is orders of magnitude above it, including the near-circular stretch of a coupler curve that a six-bar builds its approximate dwell out of.

The arc that is concentric with the pivot

A rotation carries a curve into itself exactly when the curve is an arc of a circle about the centre of rotation. Every exact dwell on this site is that one sentence applied — a cam's dwell, a Geneva's locking disc, a deadbeat escapement's locking face — and the six-bar dwell that is merely very good is what happens when the curve is nearly one.

timing · Intermittent 30 teeth and two pallets. An escape wheel of 30 teeth and a pair of pallets spanning 4 tooth pitches. The heavier line at each pallet is the locking face, here an arc about the arbor; the lighter one is the impulse face the tooth slides along once it is let go. The wheel is drawn where the contact puts it, not where it looks well: at this pallet angle the tooth in play sits on the lock face and the wheel is -0.0323° from it. Dragging the pallet through its whole engagement moves the wheel by 0.107° of recoil. Of the 6.0° the wheel turns each beat, -37.3% is drop and does nothing.

The escapement that could not alternate

Four drawings of intermittent mechanisms that appear everywhere and would not work: pallets spanning a whole number of teeth, a pawl whose pivot is on the wrong side of the tooth face, a Geneva at the wrong centre distance, and an intermittent gear with no locking arc. Each one is put through the library that draws the working version, and each returns a number.

wrong · Misconception A quantity that is not there, refusing to converge. A second central difference of a function with a bounded second derivative settles as the step is halved; across a step in the first derivative it doubles, every time. The rising line is a mutilated gear at the instant its teeth engage, where the driven wheel goes from stopped to full pitch-line speed: its successive estimates grow by a factor of 2.000000, which is the signature and not an accident of the step. The flat line is a six-slot Geneva at the same point in its cycle, whose pin enters along the slot and whose acceleration is a number. This is the only way to report an acceleration that does not exist: not by quoting a large one, but by showing the measurement refuse.

The gear with its teeth cut away

Leave teeth on part of a gear's circumference and take the rest off, and the output turns for part of the input's revolution and stops for the rest. It is the cheapest intermittent drive there is and it engages at full speed, so its output's velocity has a step and its acceleration is not a large number — it is not a number, and the way to report that is to watch a difference quotient refuse to converge.

timing · Intermittent The fork and the roller, which is a Geneva pair. A lever escapement's fork with the balance's impulse pin inside it. The pin is on a roller of 0.150 against a fork of 1.00, and the slot points at the pin — which is the entire kinematic relation and is the same one a Geneva drive's pin and slot obey. The same eight lines answer both, and the check is that they reproduce the cams field's independently written Geneva solution to fourteen figures. The pin is in the fork for 44.4° of the balance's swing out of 540°, so the balance is left alone for 91.8% of the beat. Drag the balance.

Detached, and safe while detached

A lever escapement touches its balance for a twelfth of each beat and leaves it alone for the rest. What connects the two is a pin entering a radial slot — the same pair a film projector's Geneva drive is made of, solved by the same eight lines — and the sine rule then fixes the balance's lift angle at 44.4°, which is the number a Swiss lever is specified at.

timing · Intermittent One pin and two, on the same wheel. A 6-slot Geneva wheel at one instant of its index, driven by a crank carrying one pin and by the same crank carrying two. The wheel, the slots and the centre distance are identical; only the pin count differs. Each pin drives the wheel through one slot pitch while the driver sweeps 120°, so 1 pin gives 1 index a driver turn and leaves 67% of it at rest, 2 pins give 2 indexes a driver turn and leave 33% of it at rest. Nothing else about the mechanism changes, which is why the whole question is arithmetic.

Two pins and no dwell at all

Put a second pin on a Geneva's crank and the wheel indexes twice a turn instead of once, at a quarter of the acceleration for the same output rate. Put a third on a six-slot wheel and it never rests; put a third on an eight-slot wheel and two pins meet in two slots and it jams. Both of those look like separate conditions and are one, and the boundary between them is an equation in integers with exactly three solutions.

timing · Intermittent A Geneva's acceleration against three cam laws, at the same index angle. The output's acceleration through one index, divided by the step over the square of the input angle it takes — the unit in which a cam law's acceleration coefficient is quoted — so every law is one fixed curve whatever the step. The dark curve is a Geneva of 6 slots: its step is 360°/6 and its input turns 120° while indexing, and a cam indexer is given exactly those two numbers. The Geneva's coefficient is 5.653 against cycloidal 6.283, modified sine 5.528 and simple harmonic 4.935, so at 6 slots modified sine and simple harmonic have the lower peak. The Geneva's curve starts and ends away from nought, at tan(π/6) = 0.577 in absolute terms: its acceleration steps the instant the pin enters. Dragging the slot count moves only the Geneva.

When the index law becomes a choice

A Geneva's motion law is forced by its slot count and a cam indexer's is chosen, so the fair comparison gives the cam the Geneva's own index angle and step. On peak acceleration the cam wins only below a slot count that depends on the law — 5.19 for cycloidal, 6.23 for modified sine, 8.06 for simple harmonic — and above it the Geneva does. What no slot count removes is the step: the pin arrives with an acceleration of exactly tan(π/n).

timing · Intermittent The disc, the wheel, and what has to be cut out of it. A 6-slot Geneva at 0° of driver, with the driver's locking disc of radius 27.0 drawn about its axis and the wheel drawn as the material it actually has — inside its rim, outside the 6 concave locking arcs cut into it, and clear of the 6 slots. The disc and the wheel share the region near the line of centres, so the disc has to be cut away wherever the wheel is ever there while the pin is driving. Swept over the whole index that cut-away spans 236.3°, against an index sweep of 120° — it is wider, because the rim is still swinging through the disc's circle after the pin has left the slot.

The disc decides the pin count

A Geneva's pin count is usually bounded by the slots: p indexes must not overlap, so fewer than 2n/(n−2) pins fit. The other half of the mechanism has its own inequality and nobody had measured it. The locking disc must be cut away wherever the wheel passes through it, that cut-away is wider than the index sweep at every slot count, and it is the binding condition everywhere — one pin only, from four slots upward.

timing · Intermittent

Named alongside it

The objects these essays reach for when they reach for this one.

DwellIntermittent motionIndexingMotion lawAccelerationJerkTangential entryEscapementCamDesign ruleRatchetBase circle

All concepts