Machine Kinematics
solved, then drawn
Concept

Translation — where it appears

A rigid motion in which every point moves the same distance in the same direction, so nothing turns. It is the degenerate case in which there is no instantaneous centre at all, which is why a pitch point can fail to exist.

Named by 5 essays across 4 fields — each of them below, with the objects they name alongside it.

Three bars and four bars. On the left, two bars to a common point: three links, three joints, and Grübler gives 3(3−1) − 2(3) = 0. The Jacobian agrees — two free coordinates, rank 2, nothing left over — and the shape cannot change without a bar changing length. On the right, one more bar and one more joint gives mobility 1, and the whole of this site follows from that difference. The triangle is why bridges are triangulated and the quadrilateral is why machines are not.

What decides whether it moves

Before a mechanism does anything it has to be able to. Two bars pinned to a point cannot move; three can. The count that separates them is one subtraction, it is the first thing anybody computes about a machine, and it can be wrong in a way that no amount of care with the arithmetic will catch.

constraint · Mobility The Sarrus linkage at 0°. Two three-joint chains in perpendicular planes, joining a fixed plate to a moving one. The left chain's three axes are all parallel, so it allows the plate to move in its plane; the right chain's are parallel to a perpendicular direction and allow the plate to move in that one. What both permit is a straight line, and only a straight line. Six revolute joints in a single loop: Kutzbach says 0 degrees of freedom, the screw system has rank 5 and says 1, and the plate rises. Measured over 24 positions, its tilt never exceeds 2.5e-14 radians and it never leaves the axis by more than 6.8e-14 — exact, from pin joints, with no approximation anywhere in it.

Sarrus, and the straight line that is exact

The planar answer to the straight-line problem took two hundred years and arrived as an inversion cell with eight bars. There is a six-bar answer that is also exact, that was published eleven years before Peaucellier's, and that works for a reason with nothing to do with inversion — it leaves the plane.

spatial · Spatial A screw of pitch 0.25. A single screw drawn from its own decomposition. The six numbers of the twist go into a decomposition that returns a direction, a point on the axis and a pitch of 0.2500; the helix is then the path of a point at radius 0.5 about that axis, advancing 0.250 along it per radian turned. Over 1.15 turns the point advances 1.806 — the pitch times the angle, which is what pitch means. This screw is a screw.

Every motion is a screw

Chasles showed that any rigid displacement whatever is a turn about some line together with a slide along that same line. Not approximately, and not usually — always, with the line and the amount of slide computable from the motion. It is the fact that makes spatial kinematics a subject rather than a pile of special cases.

spatial · Spatial Three bars, and no rotation left. Each of a delta robot's legs ends in a parallelogram, which keeps the bar on the platform parallel to the bar on the arm. That leg therefore permits the platform no turn about either direction perpendicular to its bar: it imposes two couple constraints, drawn here as rings about the directions they act on. Three legs impose 6; together they span only 3, so 3 are redundant. What is reciprocal to them is three couples — three pure translations, and the platform cannot turn at all.

Why the platform stays flat

A delta robot has three legs and three freedoms, and there is no obvious reason those freedoms should be the three translations rather than some mixture. The reason is a parallelogram in each leg, and the argument from there to "the platform cannot turn at all" is a constraint computation that takes six wrenches and a rank.

parallel · Parallel A joint with no way out in the plane it is drawn in. A dovetail. The tail is wider at its far end than at the mouth it went in through, so every direction out of the mouth is blocked by a slanted face and every direction further in is blocked by the floor. In the plane of this drawing the joint cannot be taken apart at all, and the direction it does come apart in is the one the drawing does not show. The moving part touches the rest at 3 faces, each contributing one inequality on the direction it may be translated in — the direction must not have a negative component along that face's inward normal — and the set of directions that satisfy all of them is a cone in two dimensions rather than three, because a translation has no moment term. That is why a removal cone can be drawn as an angle where a mobility cone cannot. Here it is empty: every direction is refused by one face or another, so the part cannot be taken out by any translation and cannot have been put in by one either. That is a statement about the assembly and not about the part, and the direction the joint does come apart in is perpendicular to this drawing. positioned by solving, not by drawing.

Which way it comes out

Drop the rotation from the inequalities and the cone lives in two dimensions rather than three, so it can be drawn as an angle: a block in a vee has ninety degrees of directions out, a key in a slot has exactly one and no arc around it, and a dovetail has none at all. Three answers, and each of them is a different kind of joint.

holding · Restraint

Named alongside it

The objects these essays reach for when they reach for this one.

ConstraintCouplePitchScrewTwistBlockingChasles's theoremContact normalDead centreDegrees of freedomthe delta robotDisassembly

All concepts