Machine Kinematics
solved, then drawn
Concept

Belt drive — where it appears

Motion carried between two pulleys by a flexible band, in a proportion decided by the radii at which the band runs. The two radii are linked by the belt's length, so a belt drive's ratio is a solve rather than a choice whenever either pulley can change its running diameter.

Named by 11 essays across 3 fields — each of them below, with the objects they name alongside it.

One routine, six strand systems. Every row is the same function: a list of bodies, each with a sense, handed to a routine that returns the tangent runs between them, the arcs on them, and the total. Nothing in it knows what a belt is, what a tackle is or what a tendon is. The right-hand column is what each row was checked against — a textbook formula, an integer, a convex hull's perimeter, a second route to the same length — and it is the reason the middle column can stay the same all the way down. positioned by solving, not by drawing.

A member with no length of its own

Every link of a pin-jointed machine holds two points at a distance, in both directions, and a configuration is the root of an equation. A belt, a rope and a tendon do neither: a strand's path is decided by the bodies it touches, and its constraint is an inequality that does nothing at all until it is taut.

strands · Strand Four tangents, and the two signs that choose between them. Two circles admit four common tangents, and a strand takes whichever one its two wrap senses name. Same sense at both ends — both centres on the same side of the strand — gives the two outer tangents, each 169.0444 mm long. Opposite senses give the two that cross between the circles, each 154.9193 mm. There is no search and no case analysis anywhere in this: the run's length is √(D² − Δ²) with Δ the signed radius difference, and changing one sense changes Δ from -18 to 70. positioned by solving, not by drawing.

Where a strand leaves a body

A taut strand meets the surface it lies on at a right angle, and every book draws it that way. It is not a rule about strands: it is what being shortest looks like, and a family of paths that were never told about tangency has its minimum exactly there — 200.64346 mm against the construction's 200.64346.

strands · Strand What the wraps add up to, and what decides it. Four runs this field draws, with every wrap angle signed by the way the strand goes round its body. The right-hand column is their sum divided by a full turn, and it is a whole number every time — the turning number of a closed plane curve, arrived at by adding up a handful of angles that were computed one at a time from tangent lines. It is 1 for a loop that goes round its pulleys once and 0 for a crossed belt, whose two wraps are equal and opposite whatever the two radii are. The serpentine's idler contributes -25.3°, and the total is still exactly one turn: a tensioner lengthens the path without changing what the path is.

The wraps add up to a turn

Every wrap angle in a closed run is computed on its own, from a pair of tangent lines that knows nothing about the others. Signed by which way the strand goes round, they add to exactly one turn — or to exactly nothing, for a crossed belt — and the integer is decided by the route rather than by any of the geometry.

strands · Strand Four pulleys, one idler, and one equation. A closed strand over four fixed pulleys and an idler carried on an arm. The idler sits outside the loop the other four make and bulges the strand out to reach it, so its wrap is signed the other way — -25.34° against the four positive ones — and the five still add to exactly one turn. The arm angle is not a free choice: the strand has a length, and matching it is one scalar equation, whatever the number of pulleys. At this position the run is 1018.046 mm and the idler takes up 0.4387 mm of strand for every millimetre it moves along the bisector of its two spans. positioned by solving, not by drawing.

The tensioner is the unknown

A linkage closes when a vector comes back to where it started: two equations, two unknowns. A strand closes when a number does — its length — however many bodies it runs over. So a run with one free body is determined, a run with two is not, and the arm angle that takes up 1,020 mm of belt is the root of one scalar equation solved to 1·10⁻¹³ mm.

strands · Strand A ratio with no steps in it. Two pulleys whose sheaves slide on their shafts, and one belt. Pushing the primary's sheaves together makes the belt ride further out; the secondary's radius is then not a choice, because the belt is a fixed length and its length over two pulleys at a fixed centre distance is a function of both radii. So the secondary's radius here is the root of that equation, solved rather than assumed, and the drawn belt is the length it is supposed to be to 0.0e+0 mm. Ratio 1.000, with the two radii adding to 110.00 — a number the received rule of thumb says should not change and which changes by 2.6% across the travel.

A ratio with no steps in it

Push a variable pulley's sheaves together and the belt rides further out. The other pulley's radius is then not a choice — the belt has a fixed length — so it is the root of an equation, solved rather than set. The rule of thumb that says the two radii add to a constant is true to first order and wrong by 7.4% of the ratio at full shift, and the departure has a closed form.

transmission · Transmission What a belt ratio's tolerance is made of. The three ways a variator's ratio can be wrong when the parts are wrong, at a nominal ratio of 1.848: a belt 0.3% long, a centre distance 0.2 mm out, and a sheave 0.15 mm from where it was commanded. Worst case they add to 2.98% and combined in quadrature they are 2.04% — the two conventions the practice field already argues about. The last row is a gear train's ratio under the same treatment, and it is empty: there is no length in a tooth count for a tolerance to be on.

The ratio that has a tolerance

Every dimension in this collection has been given a range at some point, and the ratios never were, because a gear ratio is a count and a count has no tolerance. A belt ratio is a quotient of two solved lengths, so every length in the mechanism is in it — and the amplification from belt length to ratio runs from 2.7 to 6.4 across the travel, which puts a whole per cent on a mechanism whose gearbox equivalent has none at all.

practice · Tolerance One belt, five steps. Two stepped pulleys 400 mm apart, each with five steps whose radii on the two shafts always sum to 160 mm, giving five speeds a factor of 1.6 apart. The belt is on step 4: 98.46 mm driving 61.54 mm. Solid: an open belt, 1306.066 mm on this step against 1302.655 mm on the middle one. Dashed: a crossed belt, 1367.552327 mm — the same on every step, because a crossed belt's length depends on the two radii only through their sum. Faint circles are the other steps. Dragging moves the belt to another step.

One belt for every step

A lathe changes speed by moving one flat belt between the steps of two stepped pulleys, so every pair of steps has to take the same belt. A crossed belt's length depends on the two radii only through their sum, so steps whose radii sum to the same value take the same crossed belt exactly — to the last bit of the arithmetic, over 266 random pairs. An open belt's length depends on the difference too: at constant sum it grows by d²/C, then d⁴/12C³, so an open belt made for the middle step of a five-speed pair is 12.3 mm short on the outer steps, and those steps must give up 3.74 mm of radius sum to take it.

strands · Strand One open belt on two drums. Two identical drums on parallel shafts 400 mm apart, one reversed against the other, seen from the side; the belt runs between them at a station 60 mm from the middle of its 300 mm travel. The drums are cut so that the speed ratio grows by the same proportion for every millimetre the belt is moved — from 1/2.56 to 2.56 over the travel — and so that one open belt fits at every station. At this station the driving radius is 94.45 mm, the driven 64.85 mm, a ratio of 1.456. The profiles are not cones, but the difference is a millimetre or two on radii of eighty and cannot be seen at this scale; the figures below measure it.

A cone drive is not two cones

Take a stepped pulley to its limit and the belt runs on two drums, shifted continuously along them. Drawn, the drums are straight cones of opposite taper, and a crossed belt fits them everywhere because their radius sum is constant. But straight cones grade the speed unevenly — 0.58% per millimetre of shift in the middle, 0.72% at the ends — and an evenly graded drive needs drums whose radii are logistic curves. And an open belt, the common kind, fits neither: on a lathe-sized drive it is 12.3 mm short at the ends, and two identical drums that take it and keep the grading must each be shaved in proportion to their radius, 2.69 mm at the large end and 1.05 mm at the small.

strands · Strand The drums a ratio law asks for. The two drum radii along the travel for the law speed even, the power λ of the ratio changing evenly (its logarithm at λ = 0) with λ = 1, over the range 1/2.56 to 2.56 in 300 mm, with a crossed belt so that the radii sum to 160 mm everywhere. Faint: the even proportion's logistic drums; dotted: the driven drum turned end for end, which lies on the driving drum only if the two are one shape. For this law they are not: the two shapes differ by up to 30.7 mm. The driving drum departs from the straight cone between its end radii by up to 16.18 mm, and its steepest taper is 30.8° from the drum's axis, against the straight cone's 13.2°.

A drum for every law

A cone drive's drums can be cut for any ratio law along the travel, not only the even proportion a machine tool wants. A crossed belt fits every law whose ratio stays positive, and one open belt fits any of them after a shave that depends only on the ratio at each station, so one table of shaves serves them all. What the law decides is everything else. Only the even proportion keeps the two drums one shape; the speed changing evenly or a fan's power changing evenly each need two different drums, 30 and 55 millimetres apart, and pack the change of speed into the slow end at three and fifty times the even law's rate.

strands · Strand Softening a law is drawing a taut string through its tolerance. The speed even law's ln q along the share of the travel (dashed), the tube of speeds within 11% of it with both ends of the range kept exact (shaded), and the law with the least peak grading anywhere in the tube (solid): it climbs from the slow end at the least peak slope the tube allows until it rejoins the demanded law, at 26% of the travel, and from there is the demanded law exactly; it never lags by more than the tolerance. The dotted line is the even proportion. Exact, the law needs 884 mm of travel for a belt that needs 300 mm on the even proportion; softened by 11%, 547 mm.

A tolerance shortens the drum

A cone drive's drums must be long enough that a belt never straddles too large a change of ratio across its own width, so a demanded speed law sets the drums' length through its steepest point. Allowed to deliver speeds within a tolerance of the demand, a law's least steep version is a taut string through a tube: the demanded law with its steep end capped, exact everywhere else. Softening the speed law by 11% shortens its drums from 884 mm to 547, where the even proportion needs 300, and leaves it exact over three quarters of the travel. What softening never does, at any tolerance a designer would accept, is turn the law into the even proportion: that needs 52% for the speed law and 165% for a fan's.

strands · Strand On even drums the law lives in the cam's groove. The station the belt must stand at on drums cut for the even proportion, 300 mm long, against the share of the operator's handwheel travel, for the speed law (solid) and for the even proportion, whose groove is straight (dotted). Speed ratios are marked at the right; on the even drums the logarithm of the ratio is proportional to the station, so the groove is the demanded law redrawn. The speed law's groove is steepest where the handwheel starts, 2.95 times the even proportion's slope, and least steep at 0.45 times it; on a barrel of 40 mm pitch radius with a 30° pressure-angle limit it needs 6.1 turns of the handwheel, against 2.07 for the even proportion.

A cam moves the law off the drums

A cone drive cut for a steep speed law needs long drums, because a belt cannot straddle a steep change of ratio across its own width. Cut the drums for the even proportion instead and let a cam between the handwheel and the belt fork place the belt, and every law runs on the same 300 mm. The steepness does not go away. The cam's groove is steeper than the even groove by exactly the factor the law's own drum was longer, 2.95 for the speed law and 44.7 for a fan's, and it is paid in handwheel turns instead of drum: six turns for the speed law against 884 mm of drum, and a fan law that needed thirteen metres becomes buildable.

strands · Strand

Named alongside it

The objects these essays reach for when they reach for this one.

StrandDesign ruleVelocity ratioWrap angleApproximationInextensibleTangencyConvex hullRoot-findingTurning numberContinuously variableIdler

All concepts