Machine Kinematics
solved, then drawn
Concept

Inverse problem — where it appears

Finding the joint values that put a mechanism's output where it is wanted. For an open chain it is the hard direction and has several answers; for a parallel platform it is the easy one and has essentially none.

Named by 4 essays across 4 fields — each of them below, with the objects they name alongside it.

What the machine draws, against where the polynomial vanishes. Two objects, found two ways. The thin line is the set where x^4 + 2x^2y^2 + y^4 − 1.2x^2 + 1.2y^2 is zero, walked over a grid with no mechanism involved. The marks are where the compiled machine's tracing point went, one per converged solve, over the 147 positions of its working arc. The machine's constraint set never mentions the polynomial, so evaluating it at each traced point is an independent check: the worst value over the whole arc is 3.7e-13. The arc is 1.30 radians of the driving angle and not the whole turn, and past that arc it draws something else.

A demand that is an equation

Every field on this site is handed its demand geometrically — three positions, a sampled path, a ratio at each angle — and hands back a mechanism that is right at those places and approximately right between them. This one is handed a polynomial, and the mechanism that comes back satisfies it everywhere it moves.

computing · Compute Three legs, one platform. A 3-RRR planar parallel mechanism at (0.20, -0.15) turned 11.5°, elbows up/up/up. The three actuator angles were computed one leg at a time and independently, which is what makes this direction cheap. The dashed lines extend each leg's second link: those are the three forces the legs can transmit to the platform, and the mechanism is controllable exactly while they stay independent. Here they miss one another by 0.651, and the smallest singular value of the three is 0.9550. At this position the platform can be turned through 206° in all before a leg runs out of reach.

The easy problem and the hard one change places

For a robot arm, working out where the hand is takes a walk down a chain and working out what the joints must be to put it somewhere is the hard part. Connect the platform by three legs instead of one and both statements reverse — and the reversal is not a matter of degree.

parallel · Parallel Three prescribed positions of a rigid body. The whole of the design problem, before any mechanism exists. A body has to occupy these three positions — each one a place and an angle, three numbers — and what carries it between them is not yet decided. A forward analysis starts from link lengths and finds the motion. This starts from the motion, and the lengths are what has to be found. The marked points are the poles: any planar displacement is a rotation about one point, so each pair of poses has one, and the arcs show the turn each represents through the body's own origin. A pole is a property of the displacement and not a mechanism — nothing has been chosen yet. 1 of the 3 poles lies outside this frame and is not drawn; near-parallel displacements push their pole a long way off.

The problem the other way round

Every essay before this one starts from link lengths and finds the motion. That is the reader's problem, because lengths are what a drawing shows. It is not the designer's problem, which is the reverse — and the reverse is hard enough that for a century the practical method was to look the answer up in a book.

synthesis · Synthesis Which of these two tracks was made by the front wheel. The rear wheel of a bicycle is towed, so it points at the front wheel at every instant: the tangent to the rear track, extended forward by the wheelbase, lands on the front track. Done that way round the tangents land a mean of 0.13 mm off; done the other way round they land 461 mm off, a factor of 3625. It is a measurement rather than an eye for tracks, and it needs neither the wheelbase nor the direction of travel to be known in advance.

Which way did the bicycle go

Two tyre tracks in mud, and a question with a definite answer. The rear wheel is towed, so its tangent extended forward by the wheelbase must land on the front wheel's track — and it does, to 0.13 mm one way round and 447 mm the other. The test needs neither the wheelbase nor the direction of travel, and it returns both.

rolling · Rolling

Named alongside it

The objects these essays reach for when they reach for this one.

Coupler curveKinematic synthesisPrecision positionAlgebraic curveAssembly-modeAtlasCircumcentreExact mechanismForward kinematicsFunction generationIdentificationInverse kinematics

All concepts