Machine Kinematics
solved, then drawn
Concept

Assembly-mode — where it appears

One of the ways a mechanism's links can be put together for the same actuator values. A parallel platform has dozens of them, they are separated by singularities, and a built machine cannot pass between them.

Named by 8 essays across 2 fields — each of them below, with the objects they name alongside it.

Three legs, one platform. A 3-RRR planar parallel mechanism at (0.20, -0.15) turned 11.5°, elbows up/up/up. The three actuator angles were computed one leg at a time and independently, which is what makes this direction cheap. The dashed lines extend each leg's second link: those are the three forces the legs can transmit to the platform, and the mechanism is controllable exactly while they stay independent. Here they miss one another by 0.651, and the smallest singular value of the three is 0.9550. At this position the platform can be turned through 206° in all before a leg runs out of reach.

The easy problem and the hard one change places

For a robot arm, working out where the hand is takes a walk down a chain and working out what the joints must be to put it somewhere is the hard part. Connect the platform by three legs instead of one and both statements reverse — and the reversal is not a matter of degree.

parallel · Parallel 6 ways to assemble the same three actuator angles. The actuators are at 216°, 48°, 144° in every panel, so the three elbows are at the same three points throughout and only the platform differs. Each pose satisfies all three legs to 6.7e-16. Found by reducing the problem to one equation in the platform angle and scanning it at 0.100° — exhaustive to that resolution and no further, which is the honest thing to say about a root count. Over a survey of 6750 actuator triples this mechanism ranges from none to 6.

One command, six answers

Lock the three motors of a planar platform and the platform can be in as many as six different poses, every one of them satisfying every leg exactly. Which one it is in was decided by how it was assembled and where it has been since — and the number of answers is not a property of the mechanism but of where the motors happen to be.

parallel · Parallel What a platform's own sensors settle. One three-legged platform, measured at 75 poses, with three different sets of sensors on it. Reading every joint angle determines 12 of the 15 numbers that describe the machine and leaves three undetermined, and one of the three is the scaling of the whole machine — every reading is dimensionless, so multiplying every length by a constant changes nothing any sensor sees. Laying a rule across two base pivots once recovers exactly one more, and the one it recovers is the size. Legs that report their own extension need no rule: a reading with a length in it breaks the scaling direction outright, and 7 of 9 come back. What none of the three determines is where the frame's origin sits, which is a convention rather than a defect.

A platform that measures itself

A three-legged platform with every joint read can be calibrated from its own sensors with no instrument in the room. Left to itself it shrinks the machine to a fiftieth of a per cent of its size — and reports a residual five orders smaller than the right answer's for doing it.

parallel · Parallel Where the assembly count changes, and a loop round a cusp. With the first motor held at 216°, each point of the square is a setting of the second and third motors, shaded by how many assemblies the platform has there, sampled on a 41 by 41 grid: 2 assemblies at 1,261, 4 assemblies at 347, 6 assemblies at 73. Each edge between two shades is a curve of direct singularities, where two assemblies merge and vanish, and two such edges meet in a sharp point. The 2 marked points are the cusps in this window, each found as a triple root of the closure equation. The dashed circle, of radius 8°, is the loop the motors are driven round; it encloses 1 cusp, the one at (101.35°, 185.32°), and starts at the open marker.

Round a cusp into another assembly

A parallel platform's assembly mode was supposed to change only through a direct singularity. Driven round a small loop of motor angles that encloses a cusp of the singular curve, the standard three-legged platform leaves one assembly and arrives in another, turned 52° from where it started, and at no point on the way is it nearer than 0.0716 to singular.

parallel · Parallel Where a calibration measures. The four-bar drawn at the 6 poses a selection chose, one over another, with the tracing point marked at each. The largest gap between consecutive chosen poses is 150°. They are spread because rows of the identification Jacobian at nearby poses are nearly the same row, which is a statement about the matrix and reads here as a picture of a machine in visibly different configurations.

The pose the machine cannot reach

A measurement plan is drawn against the nominal machine and executed on the real one, and the real one does not go quite where the drawing says. A pose that falls outside the travel returns no reading at all — which is not an error, not a failure of the instrument, and not nothing: it is a measurement of the limit position.

metrology · Parameter Two motors, two circles, two places for the hand. A planar five-bar with its motors 1.0 apart, arms 1 and distal links 1.25, at motor angles 100° and 60°. Each distal link holds the hand on a circle of radius 1.25 about its elbow, and the elbows are 1.678 apart, less than the 2.50 at which the circles would only touch, so they meet twice. The hand drawn solid is at (0.229, 1.850) with det A 0.995; the other assembly, dashed, is at (0.098, 0.001) with det A -0.995 — the same size and the opposite sign.

The smallest parallel robot

Two motors, two arms, and two links meeting at a hand: a planar five-bar is the smallest parallel robot there is. Its forward problem is two circles, so the hand has two places to be, and each is named by the sign of one determinant. That is the whole reason it cannot do what the three-legged platform does, and cannot change assembly without passing through the one configuration where the two meet.

parallel · Parallel One set of lengths, two machines. Three measured input–output pairs, marked, and the linkage Freudenstein's relation returns from them — which is the truth's four lengths to fourteen figures. The relation is a statement about the two angles and it holds on both assembly branches, because it was derived by squaring and that is the step that forgets which one the mechanism is on. So the identified linkage assembled the way the data was taken passes through every reading, to 2.53e-14 radians, and assembled the other way misses them by up to 268° — at the first precision point it reads -111.6° where 98.8° was wanted. That is not a near miss and not a failure either. It is the other answer.

One set of lengths, two machines

Three measured input–output pairs return a four-bar's four lengths to fourteen figures. Assembled the way the data was taken, that linkage reproduces every reading to 2.5 × 10⁻¹⁴ radians. Assembled the other way — which the same four lengths permit — it misses them by 268°, and no equation in the identification knows the difference.

metrology · Parameter Which numbers have a size. Twelve quantities from eight fields of mechanism kinematics, each scaled by taking every length in its mechanism up and down together and fitting the power its value follows. A shape lands on zero, a length on one, a curvature on minus one, an area on two, and every row lands on an integer to 3.3e-11. The sorting is not a units argument — it is measured from each field's own library, by asking that library the same question. What it says is that most of what kinematics computes is a shape: a mobility, a Grashof class, a transmission angle, a contact ratio and a velocity ratio are all unchanged by making the machine bigger, so all of them are recoverable from a measurement that cannot recover a single length. The row worth stopping at is the tolerance band: held to a fixed ±0.01 it lands on minus one, because ±0.01 is a length and a bigger machine held to the same absolute tolerance is a better machine. Written as a percentage the same band lands on zero. One quantity, two drawing conventions, two different kinds of number.

A count is neither

Every quantity in the scaling survey lands on an integer power — zero for a shape, one for a length, two for an area. A mobility lands nowhere. It has no dimension at all, it does not move under any perturbation, and the probe that sorts the rest of the site's numbers returns nothing for it.

metrology · Parameter

Named alongside it

The objects these essays reach for when they reach for this one.

Forward kinematicsWorking modeCalibrationDirect singularityIdentifiableParallel mechanismCuspidal mechanismGrashof's conditionIdentification jacobianMeasurement residualNewton–RaphsonParallel manipulator

All concepts